Southwing SA505 English, Introduction, Charging The Headset, USB charging, Normal pairing, Index

ENGLISH

USER GUIDE

SA505

Bluetooth® Wireless Headset

INDEX
	Introduction	3
1.	Charging the Headset	3
2.	Turning the Headset on and off	3
3.	Pairing the Headset	3-4
4.	General Usage	4-5
5.	Push4TM call	5
6.	Additional Functions	5
7.	Troubleshooting	6
8.	Additional Information	6-7
9.	Declaration of Conformity	8
10. Command Summary		9

The SA505 is compatible with Bluetooth enabled mobile phones; Bluetooth enabled music players and Bluetooth USB and audio adapters (dongles). All of these will be referred to in this guide as “Bluetooth device”.

Note:

Please read the “Safe Usage Guidelines” and “Limited Warranty” before using the Headset.

INTRODUCTION

Thank you for choosing a Bluetooth® pro- duct from SouthWing.

This user guide provides all the information you will need to use and care for your product.

All relevant information regarding your SouthWing product can be found on the support section of our website:

www.south-wing.com

1. CHARGING THE HEADSET

You will need to charge the battery of your Headset. To do so, follow these steps:

1.Make sure the Headset are turned off

2.Plug the power supply into a power point

3.Plug the connector of the power supply into the USB Charging Socket [1]. The Charging Light [3] will turn orange to indi- cate the Headphone battery is charging

4.Once the Charging Light [3] turns off, the Headset are fully charged and can be removed from the power supply

USB charging

Thanks to its USB charging facility, the Headset battery can be charged from any USB port, such as those found on a PC or laptop, by using the SouthWing USB cable adaptor accessory.

Please Note:

·The Headset will not function while charging.

·If the Charging Light [3] remains off when charging, the battery is already fully charged and does not require further charging.

·To maximise battery life, do not charge the Headset for extended periods of time.

·Full battery capacity will be achieved after two or three full charge/discharge cycles.

·When your battery is flat, it takes up to three hours to completely charge your Headset

·Only use SouthWing power supply or accessories for charging.

2. TURNING THE HEADSET ON AND OFF

Before turning the Headset on, make sure the microphone is in the up position as in Figure 2. To turn the Headset on, move the Power switch [2] to the ON position. A short tone will be heard and the Status Light [10] will start flashing slowly in red. When the Headset is turned on, it will automatically connect to the last phone and stereo music devices that were connected.

To turn the Headset off, move the Power switch [2] to the OFF position.

3. PAIRING THE HEADSET

Auto-pairing

For added convenience, your Headset has an auto-pairing function so that when you turn the Headset on for the first time, it is already in pairing mode. The Status Light [10] will flash blue and red alternately and 2 short tones will be heard. Then, follow these steps:

1.Put the other Bluetooth device into pair- ing mode (see the instructions which came with your device). Ensure that the Bluetooth device is no more than 1 metre away from the Headset.

2.Enter the PIN number: 0000. If pairing is successful, the Status Light [10] will flash slowly in red.

Normal pairing

You will need to follow the steps below if you want to pair your Headset with another Bluetooth device. Your Headset will store the pairings of 5 devices. You may pair to more devices, but each new device will replace a previously paired device.

1.Press and hold the Play Button [7] for about 5 seconds until the Status Light [10] flashes blue and red alternately and 2 short tones are heard

2.Then complete normal pairing process by following points 1 and 2 of the auto-pair- ing section above.

2

® Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. U.S.A. and licensed to SouthWing. 3