NOTE. Wear eye protection when cleaning out the pulley area.

3.With the three continuous “V” profiles on the in- side, place the new belt over the bottom pulley.

+DOIILWWKHRWKHUHQGRIWKHEHOWRQWKHWRSSXOOH\ then roll the belt in place whilst turning the pul- ley.

4.Check that the belt runs evenly by manually turning the belt.

5.Replace the cover and the four fixing screws.

5HSODFHWKHHOHFWULFDOSOXJDQGUXQWKHSODQHU for a minute or two to make sure that the motor and belt are operating correctly.

ACCESSORIES

Parallel guide; spare driving belt; spare set of 2 blades; dust bag; spanner.

VII - Maintenance

CAUTION: Always ensure that the tool is switched off and unplugged before attempt- ing to perform inspection or maintenance.

5HJXODUO\FKHFNWKDWDOOWKH¿[LQJVFUHZVDUHWLJKW They may vibrate loose over time.

Re-lubricate all moving parts at regular intervals.

CAUTION: Water must never come into contact with the tool.

IMPORTANT! To assure product safety and reli- DELOLW\UHSDLUVPDLQWHQDQFHDQGDGMXVWPHQW LQ-

FOXGLQJEUXVKLQVSHFWLRQDQGUHSODFHPHQW VKRXOG

EHSHUIRUPHGE\FHUWL¿HGVHUYLFHFHQWUHVRURWKHU

TXDOL¿HGVHUYLFHRUJDQLVDWLRQVDOZD\VXVLQJJHQ- uine replacement parts.

VIII - Warranty

The guarantee period for SPARKY power tools is determined in the guarantee card.

)DXOWVGXHWRQRUPDOZHDURYHUORDGLQJRULPSURS- er handling will be excluded from the guarantee.

)DXOWVGXHWRGHIHFWLYHPDWHULDOVLPSOHPHQWHGDV well as defects in workmanship will be corrected free of charge through replacement or repair.

The complaints for defective SPARKY power WRROV ZLOO EH UHFRJQL]HG LI WKH PDFKLQH LV VHQW back to the dealer or is presented to the author- ised warranty service centre undismantled, in its initial condition.

BRUSH REPLACEMENT

When the carbon brushes are worn out, both brushes must be replaced simultaneously with genuine brushes at SPARKY service centre for warranty and post-warranty service.

CLEANING

)RUVDIHRSHUDWLRQDOZD\VNHHSWKHPDFKLQHDQG its ventilation slots clean.

Regularly check to see if any dust or foreign matter has entered the grills near the motor and around the switches. Use a soft brush to remove any ac- cumulated dust. Wear safety glasses to protect your eyes whilst cleaning.

If the body of the tool needs cleaning, wipe it with a soft damp cloth. A mild detergent can be used.

CAUTION:1HYHUXVHDOFRKROSHWURORU RWKHUFOHDQLQJDJHQW1HYHUXVHFDXVWLFDJHQWV to clean plastic parts.

Notes

Carefully read the entire Instruction Manual before using this product.

With continuing product development changes may have occurred which render the product received slightly different to that shown in this in- struction manual. The manufacturer reserves the

ULJKWWRFKDQJHVSHFL¿FDWLRQVZLWKRXWQRWLFH

6SHFL¿FDWLRQVPD\GLIIHUIURPFRXQWU\WRFRXQWU\

EN 8

pages-P282.indd 8

P 282

ɝ

Page 10
Image 10
Sparky Group P 282 instruction manual VII Maintenance, Viii Warranty, Accessories, Brush Replacement, Cleaning