Charging the Accumulator, Normal | Stanley Black & Decker MB656

CHARGING THE ACCUMULATOR

	The tools required to charge the breaker accumulator	NOTE:
	are the Charge Hose assembly (505232) and the Ac-	When disengaging the tester a “POP” of nitrogen is
	cumulator Tester (28257), which are used with other
		normal.
	Stanley model breakers. When charging the accumula-
		6. Connect the charge hose assembly to the charg-
	tor, make sure the tools and charge valve is clean. Dirt
	can contaminate the charge valve and cause leakage.	ing valve on the tester. Make sure the valve on the
	1. Remove the protective plug from the accumulator	charge hose assembly is closed. Open the valve on
		the nitrogen bottle.
	charge valve.
		7. Very slowly open the valve on the charge hose as-
	2. Hold the chuck end of the tester and turn the gauge
		sembly and slowly meter the nitrogen into the break-
	fully counter clockwise to ensure the plunger inside
		er charge valve until the tester reads the correct
	the chuck is completely retracted.
		charge pressure.
	3. Screw the tester into the breaker charge valve by
		8. When the correct pressure is obtained, close the
	turning the chuck. Do not use the gauge for turn-
		valve on the charge hose assembly and on the nitro-
	ing as this will advance the plunger in the chuck.
		gen bottle. Unscrew the gauge to retract the plung-
	Tighten the chuck lightly against the breaker charge
		er. Loosen and remove the tester from the charge
	valve.
		valve. Before replacing the protective plug, inspect

	4. Turn the gauge clockwise to advance the plunger	the plug O-ring. If damaged or deformed, replace
	until a pressure is indicated on the gauge. Do not	the plug. Apply Loctite™ 242 to plug and cap.
	overtighten.

5.If the pressure is correct, unscrew the gauge to re- tract the plunger. Then, loosen and remove the tes- ter from the charge valve. If the pressure is not cor- rect, proceed to Step 6.

CHARGE PRESSURE SPECIFICATION

Main Accumulator:	350 PSI +/- 10 PSI
	24 BAR +/- .7 BAR
Main Accumulator
P/N 28257 Tester
P/N 505232 Charge Hose Assy
	MB656 User Manual ◄ 17

Image 17

Stanley Black & Decker MB656 user manual Charging the Accumulator, Normal

Contents

MB656 Weisbeck, Andy Declaration of Conformity Table of Contents Local Safety Regulations Safety Symbols Safety Precautions Know the Work Conditions Obey Safety RulesBe Thoroughly Trained Before Operating the Unit Alone Parking Brake Tool Stickers & Tags 66219 Guaranteed Sound Power Level Sticker Operation PRE-INSTALLATION InstructionsPRE-OPERATION Procedures Long Term Storage Operating a BreakerPreparation for USE Positioning the Carrier Backhoes Positioning the Breaker Tool on the Work Material Breaking Maintain Down Pressure Blank Firing Grease the BIT Underwater Usage Problem Cause Solution Troubleshooting Tool Stop and Lower Bushing MaintenanceDaily Maintenance Checks Normal Charging the Accumulator Hose Routings Flow Control KIT Instructions Lower Bushing Item Wear TolerancesTool Stop Item Retainer PIN Item WORN-OUT Front Bushings or Retainer Pins Tool Failure not Covered Under WarrantyProper USE & Care of Tool Bits Blank Firing or Free Running Corrosion Prying Internal Material Flaw Tool Failure Covered Under Warranty Blunt MoilChisel Test Procedure Flow Test Procedures Heat Load Test Troubleshooting Tool Definitions Dimensions and Weights Specifications Miscellaneous Accessories MB656 Power Cell Illustration Housing Parts Illustration Charge Valve Assy Incl MB656 Parts List MB656 Mounting Brackets Page Stanley Hydraulic Tools SE Naef Road Milwaukie, Oregon