Manuals / Sterling / Power Tools / Welder

Sterling 882.00274.00 specifications Typical Additive Feeder Controllers

Models: 882.00274.00

1 51

Download 51 pages 51.35 Kb

Page 43

MOUNTING FLANGE			CONTROLS
4"	7"			SET POINT
	91 2"	SET POINT	912"
	91 2"		912"
	POWER	MOTOR
	ON	MOTOR ON AUTO
		OFF		POWER	MOTOR
	OFF	MAN	ON	MOTOR ON	AUTO
					OFF
			OFF		MAN

4"

7"

614"

614"

STANDARD	STANDARD
	WITH OPTIONS

27 34"

12"

183 4"

6"

3114"

Additive Feeder	Hopper capacity	Electrical supply	Amp	Shipping weight
Type			draw
1 Component	1.0 Cu. Ft.	115-1-60	1.3	50 lbs.
2 Component	(2) 1.0 Cu. Ft.	115-1-60	2.5	90 lbs.

Figure 7: Typical Additive Feeder Controllers

Additive Feeders

Chapter 7: Appendix

42 of 50

Image 43

Sterling 882.00274.00 specifications Typical Additive Feeder Controllers

Contents

SF Series Additive Feeders Parts and Service Department Shipping Information Table of Contents Troubleshooting How to Use This Manual SafetySafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves General Responsibility ResponsibilityRemember Operator ResponsibilityReporting a Safety Defect Maintenance ResponsibilityModels Covered in This Manual Standard FeaturesMechanical Features Functional DescriptionController Features Electrical FeaturesOptions Accessories Safety Circuit Standards Safety Devices and InterlocksFail Safe Operation Safety Device Lock-Outs Rigging and Placing the Additive Feeder InstallationSupply System Installation Uncrating the EquipmentElectrical Connections Main Power ConnectionControl Relay Connection Determining the Desired Feed Rate Setup Procedures110 100 Procedure Calibration ProcedureEquipment Needed Observed Feed Rates ExamplesShutting Down the Additive Feeder Initial Start-upPre-Startup Checks Starting Up the Additive FeederStart-up SwitchesIndicator Lights OperationUsed as a Cycle Override Safety Timer Timer ModuleCounter Module Elapsed Time Module Dual Setpoint Control Operation 2 Component Applications Regrind Feeder with Proximity SwitchSet Point #2 Motor Control Bottom Low Level Extruder Tracking Control Extruder Tracking Installation and SetupExtruder Tracking Equation Motor RPM = 25.2 X Auger RPM Desired Display SettingField Control Programming EquationViewing or Changing the Constant Programming ModeProgramming for Follower Operation Program Minimum Setting Viewing or Changing the Program Minimum SettingViewing or Changing the Program Maximum Setting Exiting Programming Mode and Returning to Run ModeShutting Down the Additive Feeder Additive Feeder Control Factory DefaultsPreventative Maintenance Schedule MaintenancePhotocopy this page for your maintenance records Material Cleanout/Changeover Preventative MaintenanceInstalling Auger Assembly Corrective MaintenanceAuger Assembly Changeover Removing Auger AssemblyReplacement Motor Brush Part Numbers Motor Brush ReplacementProblem Possible cause Corrective action TroubleshootingIntroduction Additive Feeders Troubleshooting Appendix WarrantyOptional Components Annex B Information Technical SpecificationsAdditive Feeder Specifications and Overall Dimensions Drawings and DiagramsTypical Additive Feeder Controllers SET Point Exploded Assembly Drawing Parts List Spare Parts ListA0541292 Auger Assembly, 1/2 One Component Control Enclosure Parts Identification Two Component Control Enclosure Parts Identification Returned Material Policy Safety Tag InformationWarranty Returns Additive Feeder Safety TagsTechnical Assistance Additive Feeder Identification Serial Number TagPhotocopy this page for your records Worksheet for Charting Feed Rates