Manuals / Sun Microsystems / Computer Equipment / Network Card

Sun Microsystems SG-XPCIE2FC-EM8-Z, SG-XPCIE1FC-EM8-Z manual To Apply Power, LED Status

Models: SG-XPCIE1FC-EM8-Z SG-XPCIE2FC-EM8-Z

1 56

Download 56 pages 20.46 Kb

Page 40

Image 40

FIGURE 2-4Attaching the Optical Cable

2. Connect the other end of the cable to the FC device.

After the optical cable is connected to the HBA, you can power on the system.

▼To Apply Power

1.Verify that the HBA is securely installed in the system.

2.Verify that the correct fiber-optic cable is attached.

3.Refer to your system installation or service manual to determine how to power on the system.

▼(LED) Status

Yellow and green LEDs can be seen through openings in the mounting bracket of the HBA. Each port has a corresponding set of yellow and green LEDs (see FIGURE 2-5).

14 Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008

Page 40

Image 40

Sun Microsystems SG-XPCIE2FC-EM8-Z manual To Apply Power, LED Status, Connect the other end of the cable to the FC device

Contents

Sun StorageTek 8 Gb FC PCI Express HBA, Emulex Installation Guide For HBA Models SG-XPCIE1FC-EM8-Z and SG-XPCIE2FC-EM8-ZSun Microsystems, Inc December 2008, Revision APage Contents Safety Agency Compliance Statements Preface1. HBA Overview 1 Kit Contents 2. Hardware Installation and Removal3. HBA Software Installation 4. Known IssuesSafety Declaration of ConformitySupplementary Information USA-FCC Class ADATE FCC Class A Notice Regulatory Compliance StatementsICES-003 Class A Notice - Avis NMB-003, Classe A CCC Class A Notice BSMI Class A NoticeGOST-R Certiﬁcation Mark Regulatory Compliance Statements Page Safety Agency Compliance Statements Safety PrecautionsSymbols Placement of a Sun ProductBattery Warning Conformité aux normes de sécurité System Unit CoverLaser Compliance Notice Rack System WarningSymboles Modification du matérielPositionnement d’un produit Sun Niveau de pression acoustiqueCouvercle de lunité Mise en garde relative aux batteriesMise en garde relative au système en rack Symbole Einhaltung sicherheitsbehördlicher VorschriftenAvis de conformité des appareils laser Périphériques CD et DVDLautstärke SELV-KonformitätAnschluss des Netzkabels Warnung bezüglich BatterienNormativas de seguridad Warnungen bezüglich in Racks eingebauter SystemeHinweis zur Laser-Konformität CD- und DVD-GeräteModificaciones en el equipo Colocación de un producto SunNivel de ruido Cumplimiento de la normativa para instalaciones SELVAdvertencia sobre las baterías Cubierta de la unidad del sistemaAdvertencia sobre el sistema en bastidor Aviso de cumplimiento de la normativa para la utilización de láserNordic Lithium Battery Cautions Nordic Power Distribution CautionsNordic Grounded Socket Cautions Page Preface Before You Read This BookHow This Book Is Organized SunVTS 6.X Users Guide SunVTS 6.X Reference ManualUsing UNIX Commands Shell PromptsTypographic Conventions Documentation, Support, and TrainingThird-Party Web Sites Sun Welcomes Your CommentsKit Contents “Kit Contents” on page “HBA Features and Specifications” on pageHBA Overview “System Interoperability” on pageHBA Features and Specifications Operating System and Technology Requirements TABLE 1-1 HBA Features and SpecificationsThe HBA requires the OS and technology levels listed in TABLE TABLE 1-2 Supported Operating System/Technology VersionsSystem Interoperability Host Platform Support“Host Platform Support” on page “Storage Support” on page “Quantum S4 tape drive” on page“Array Support” on page “System Support” on page Storage Support“Tape Storage Support” on page “Quantum S4 tape drive” on page Switch Support Array SupportSystem Support Tape Storage SupportEnvironmental Requirements Specification TABLE 1-4 HBA Environmental RequirementsAltitude 3200mHardware Installation and Removal Observing ESD and Handling Precautions“Observing ESD and Handling Precautions” on page “Installing the Hardware” on page “Testing the Installation” on pageInstalling the Hardware To Install the HBA“To Install the HBA” on page “To Connect the Optical Cable” on page “To Apply Power” on pageChapter 2 Hardware Installation and Removal FIGURE 2-1 Optical Transceiverf. Re-install the screws that attach the HBA to the bracket c. Remove the mounting bracket screws from the top of the HBAd. Remove the bracket and store it for future use e. Align the new mounting bracket tabs with the holes in the HBATo Connect the Optical Cable 9. Replace the computer case and tighten the case screwsTo Apply Power 1. Verify that the HBA is securely installed in the systemLED Status 2. Connect the other end of the cable to the FC deviceLED Status 1 Port 0 LEDs 2 Port 1 LEDsTesting the Installation To Verify Proper Installation for the Solaris OS“To Verify Proper Installation for the Solaris OS” on page “To Verify Attached Storage for the Solaris OS” on pagecontinued pci@7c0/pci@0/pci@9/SUNW,emlxs@0,1/fp@0,0/diskproperties command continuedok cd /pci@780/pci@0/pci@8/SUNW,emlxs@0 c ok .propertiesTo Verify Attached Storage for the Solaris OS Note - You might need to use the reset-all command before using the apply show-children command continued Replacing the SFP+ Unit on the HBA Removing the HardwareTo Remove the HBA Hardware 2. Removing the HBA hardwarePage HBA Software Installation Solaris Diagnostic Support“Installing Software For the Red Hat and SUSE Linux OSes” on page “Configuration and Diagnostic Utilities” on pageInstalling Software For the Red Hat and SUSE Linux OSes To Install the HBA Software For the Linux OSTo Install the HBA Software For the VMware Technology You must obtain the drivers from VMware2. Locate the driver section for Windows Configuration and Diagnostic Utilities3. Download the Driver Kit by clicking Download Known Issues Reboot Fails on the SPARC Enterprise M8000 System