Superior CF6500-CMP Screen Panel Kit, Remote Control Kit, Brass Hood Kit, Brass Louver Kit

12

Screen Panel Kit

An optional screen panel can be installed on the CF door. This screen panel is easy to install using the provided hardware. The screen panel can be installed with both ceramic and tem- pered glass in the door. This kit can be retrofit- ted to previously installed appliances. The screen panel kit may not be used in conjunction with the one piece decorative arch kits.

Remote Control Kit

The Model RCK adds the convenience of re- mote control for your appliance. The kit in- cludes a wireless, hand held transmitter and a receiver that replaces the wall switch. This special receiver permits either manual or re- mote control modes. Both receiver and trans- mitter operate on standard 9 volt batteries (not included). Refer to the RCK installation instruc- tion for specific details.

Brass Hood Kit

An attractive brass hood is available to be used on the CF appliance. These hoods are designed to be fitted to the face of the appliance above the door. In addition to providing an aesthetically pleasing appearance to your appliance installa- tion, the hood reduces heat effects to decora- tive mantles and finish materials located di- rectly above the fireplace opening. The hood kit includes the necessary attaching hardware. This kit can be retrofitted to previously installed appliances.

Brass Square Surround Kit

Decorative brass square surround kits are avail- able for use with these appliances. The BSK-5 and BSK-6 are designed to attach directly to the front face of the appliance at its extreme edges. The brass square surround kits provide a pic- ture frame finish for the appliance 2 ¹⁄₂" wide. Use the BSK-5 with CF5500 appliances and the BSK-6 with CF6500 appliances. The brass square surround kit can be retrofitted onto previously installed appliances.

Brass Louver Kit

Decorative brass louvers are available for use these appliances. These louvers are designed to replace the standard black louvers that are provided with the appliance. The brass louver louver kit includes three (3) plated louvers and a fourth (black) louver, that simply snap into place. They provide a touch of elegance to the CF appliance. This kit can be retrofitted to previously installed appliances.

Wall Thermostat Kit

A wall thermostat kit is available for use with these appliances. The wall thermostat is de- signed to be wired directly to the appliance millivolt gas control circuit and provide auto- matic On/Off control of the appliance to main- tain a desired temperature within the room.

Decorative Volcanic Stone

The decorative volcanic stone, Model DVS, can be used to enhance the look of your appliance. Spread the decorative volcanic stone evenly around the bottom of the firebox.

One Piece Arch Kit

A one piece complete door arch kit is available for use with these CF appliances. The kit is easy to install and does not require hardware to attach it to the standard door frame. This kit can be retrofitted to previously installed appliances. The one piece decorative arch kit can not be used in conjunction with the screen panel kit.

Gas Flex Line with Valve

A gas flex line kit is available to aid in attaching this appliance to the gas supply. This kit can only be used where local codes permit. The kit includes a ¹⁄₂" NPT to ³⁄₈" flare in line shut-off valve, a 12" flex line ³⁄₈" female flare through and a ³⁄₈" flare to ³⁄₈" NPT fitting. The components of this kit are rated for both natural and propane gas. This kit is designed to be used as an aid in installing the appliance.

WARNING: CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES. USE CAUTION AROUND THE APPLIANCE TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE SUPER- VISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.

OPERATION AND CARE OF YOUR APPLIANCE

1.Appliance operation is controlled through an on/off switch. Separate switches may provide independent control for the optional forced air kit and fireplace operation (see Optional Equipment).

2.To light the appliance refer to the lighting instructions located at the back of this manual.

Note: Instructions are also found on the pull- out panel located in the lower control compart- ment of the appliance.

3.Flame Adjustments – These appliances are equipped with a two stage, High (HI), Low (LO) gas control valve. This valve provides for easy flame height adjustment. To adjust the burner between the HI and LO settings, rotate the HI/LO knob, located in the center of the valve front face, clockwise and counter- clockwise respectively.

4.When lit for the first time, the appliance will emit a slight odor for an hour or two. This is due to the “burn-in” of the internal paints and lubricants used in the manufacturing process. Additionally, when lit for the first time, this appliance may produce smoke, this is normal and should be expected. For the first few hours, operate the appliance with doors and windows open to encourage the dissipation of smoke and fumes.

5.Upon each lighting of the appliance, conden- sation may occur and fog the inside of the glass enclosure panel. This condition is normal and will disappear as the glass surface heats.

6.Always keep the appliance area clear and free from combustible materials, gasoline and other flammable liquids.

7.Remember, these appliances have a con- tinuous burning pilot flame. Exercise caution when using products with combustible vapors.

WARNING: OBSERVE CAUTION NEAR THE GLASS ENCLOSURE PANEL. THE GLASS MAY SHATTER UNEXPECTEDLY OR IF STRUCK WITH AN OBJECT.

8.CAUTION: DO NOT OPERATE THIS APPLI- ANCE WITH A BROKEN GLASS PANEL. Where broken glass exists, the complete glass enclo- sure panel must be replaced. See the Replace- ment Parts List on page 18 for correct replace- ment part numbers. Glass enclosure panel re- moval and installation instructions are described on pages 5 and 10 respectively.