Manuals / SV Sound / Car Audio and Video / Car Speaker

SV Sound PC12-Plus, PB12-Plus Operation of the Power Mode Switch, Connectivity & Panel Operations

Models: PC12-Plus PB12-Plus

1 34

Download 34 pages 43.96 Kb

Page 7

Connectivity & Panel Operations

STA-800D/1000D Equipped Subs

SVSound™

Connectivity & Panel Operations

Operation of the Power Mode Switch

NOTE: Depending on the version of the STA-800D/STA-1000D amplifier, the LCD display may or may not light when power is first applied. Even if the LCD display does not light when power is applied, if the amplifier is in the AUTO mode, it will play source material when a suitable signal is applied.

To manually come out of Standby when in AUTO mode, press and hold the IFC knob for several seconds until the display lights. Note that menu operations are not possible when the amplifier is in Standby.

In AUTO mode If power is removed from the amplifier either through the main power rocker switch, or by loss of power from the mains (wall outlet) and then restored, the amplifier will either turn back on or come up in Standby. If it comes up in the on state, it will revert to Standby after a period of time if no signal is presented at the inputs.

When the AUTO/ON Switch is in the ON position and power is applied to the amplifier via the main power switch, the amplifier will NOT turn on. In order to turn the amplifier on, the IFC knob must be pressed and held in for several seconds. When the amplifier turns on, the LCD display will illuminate at the WELCOME screen for a few seconds. The amplifier will stay on until either the IFC knob is pressed and held until the LCD display goes dark, when power is removed from the amplifier using the main power switch, or power is removed from the mains (wall outlet).

If power is removed from the amplifier either through the main power switch or by loss of power from the mains (wall outlet) and then restored, the amplifier will not turn back on until the IFC knob is pressed and held as noted above.

It is important to note in case of a power outage, it will be necessary to manually turn the amplifier on by pressing and holding the IFC knob as noted above. STA-800D and STA-1000D Connectivity and Panel Operation.

© 2011 Specialty Technologies, LLC • Call SVSound™ 877.626.5623 • www.svsound.com

7

Image 7

SV Sound PC12-Plus, PB12-Plus, SB13-Plus, SB13-Ultra Operation of the Power Mode Switch, Connectivity & Panel Operations

Contents

Manual Version 1.5 Sep Models PB12-Plus, PC12-Plus, SB13-PlusPB13-Ultra, PC13-Ultra, SB13-Ultra Manual Version 1.4 JuneTable of Contents Important Safety Instructions Important Safety Instructions SVSound WELCOMESTA-800D/1000DEquipped Subs About your SVS Subwoofer Connectivity & Panel Operations Operation of the Power Mode SwitchSVSound Input ConfigurationInputs Connectivity & Panel OperationsSVSound Connectivity & Panel OperationsSTA-800D/1000DEquipped Subs SVSound Connectivity & Panel OperationsSTA-800D/1000DEquipped Subs SVSound If you have one of SVS’s AS-EQ1 high-resolution, multi-subwooferEqualizers, see Figure 6 for proper connec- tivity with one or more subwoofers. Also refer to your AS-EQ1Operator Manual for detailed information on connectivity and setup of the AS-EQ1into your listening environmentConnectivity & Panel Operations FIG.Outputs Power Mode SwitchMain Power Switch Power Cord1.Top-levelmenu screens Integrated Function ControllerThe IFC knob has three actions associated with it The two line LCD display has two context modesHigh Pass Filter HPF Adjustment STA-1000D VolumeIntegrated Function Controller SVSound Low Pass Filter LPF AdjustmentPhase Degree Integrated Function ControllerSVSound High Pass Delay STA-1000DRoom Gain Comp Integrated Function ControllerSVSound Subwoofer Tune Ported Subwoofers OnlyP-EQParametric EQualizer Integrated Function ControllerFrom the IFC WELCOME screen, single-clickthe IFC knob and rotate the IFC knob seven clicks clockwise until the display reads “MENU/P-EQ”. Single-clickthe IFC knob to select the PEQ1 Function or rotate the IFC knob clockwise or counter-clockwiseand single-clickto select PEQ2 Function Integrated Function ControllerSVSound STA-800D/1000DEquipped SubsSVSound Integrated Function ControllerSTA-800D/1000DEquipped Subs STA-800D/1000DEquipped Subs Integrated Function ControllerFIG.8 SVSoundUnpacking and Subwoofer Location Setup, Calibration & IntegrationSVSound Setup, Calibration & Integration Power and Signal ConnectionFIG.9 STA-800D/1000DEquipped Subs Calibrating the SubwooferSetup, Calibration & Integration SVSoundSTA-800D/1000DEquipped Subs Setup, Calibration & IntegrationAt the completion of running the auto setup routine, there are two things you should check in your AVR or pre/pro’s Manual Speaker Setup Menu to make sure your subwoofer has been integrated properly SVSoundcrossovers set no lower than 80 Hz a speaker set to Small - as opposed to Large or Full Range - will cause bass frequencies below the selected crossover to be routed from the speaker to the subwoofer Setup, Calibration & IntegrationSVSound Port TuningSTA-800D/1000DEquipped Subs Advanced Features Parametric Equalizer PEQ Setup & Use of PEQ“Q” Control Effects Setup & Use of PEQSTA-800D/1000DEquipped Subs Measuring In-RoomFrequency ResponseSetup & Use of PEQ SVSoundTo measure the FR of the subwoofer only, connect your sound card output directly to a line level input on the subwoofer. Use the Excel spreadsheet named Subwoofer Frequency Response link provided above, which will plot the frequency response of the subwoofer from 11.2 Hz to 100.8 Hz. Input your raw direct read values from your SPL meter into the green band of frequencies in the Raw SPL Data worksheet, and the Frequency Response worksheet will plot the FR of the subwoofer Setup & Use of PEQSVSound STA-800D/1000DEquipped SubsSTA-800D/1000DEquipped Subs Setup & Use of PEQAdjusting The PEQ Identify the largest/widest peak in the response and target it for reduction with the PEQ control. When making adjustments to the PEQ control, there is no need to re-plotthe entire FR for interim adjustments - simply re-plotthe affected section of the curve to verify your PEQ adjustments are having the desired effect. When you are done making adjustments, you can re-plotthe entire frequency response to obtain a final curve SVSoundSet the Frequency control to the approximate center frequency of the largest peak. Set the Q control to 14.4 narrowest bandwidth, and set the Level control to -6dB. Play the test tones again and re-measureand re- plot the affected portion of the FR curve and visually evaluate your results. Simple trial/error will then allow you to adjust all three controls to shape the PEQ cut to achieve the desired effect Setup & Use of PEQRoom Compensation Advanced Features Room CompensationSTA-800D/1000DEquipped Subs Terms & ConditionsSVSound 6420 Belmont Avenue, Girard, Ohio Fax SVSound