Manuals / SV Sound / Car Audio and Video / Car Speaker

SV Sound SB13-Plus manual Integrated Function Controller, SVSound, STA-800D/1000DEquipped Subs

Models: PC12-Plus PB12-Plus

1 34

Download 34 pages 43.96 Kb

Page 20

Image 20

STA-800D/1000D Equipped Subs

SVSound™

Integrated Function Controller

FIG.8

Page 20

Image 20

SV Sound SB13-Plus, PB12-Plus, PC12-Plus, SB13-Ultra Integrated Function Controller, SVSound, STA-800D/1000DEquipped Subs

Contents

Models PB12-Plus, PC12-Plus, SB13-Plus PB13-Ultra, PC13-Ultra, SB13-UltraManual Version 1.4 June Manual Version 1.5 SepTable of Contents Important Safety Instructions Important Safety Instructions STA-800D/1000DEquipped Subs WELCOMESVSound About your SVS Subwoofer Operation of the Power Mode Switch Connectivity & Panel OperationsInput Configuration InputsConnectivity & Panel Operations SVSoundSTA-800D/1000DEquipped Subs Connectivity & Panel OperationsSVSound STA-800D/1000DEquipped Subs Connectivity & Panel OperationsSVSound If you have one of SVS’s AS-EQ1 high-resolution, multi-subwooferEqualizers, see Figure 6 for proper connec- tivity with one or more subwoofers. Also refer to your AS-EQ1Operator Manual for detailed information on connectivity and setup of the AS-EQ1into your listening environment Connectivity & Panel OperationsFIG. SVSoundPower Mode Switch Main Power SwitchPower Cord OutputsIntegrated Function Controller The IFC knob has three actions associated with itThe two line LCD display has two context modes 1.Top-levelmenu screensIntegrated Function Controller VolumeHigh Pass Filter HPF Adjustment STA-1000D Low Pass Filter LPF Adjustment Phase DegreeIntegrated Function Controller SVSoundHigh Pass Delay STA-1000D Room Gain CompIntegrated Function Controller SVSoundSubwoofer Tune Ported Subwoofers Only P-EQParametric EQualizerIntegrated Function Controller SVSoundIntegrated Function Controller SVSoundSTA-800D/1000DEquipped Subs From the IFC WELCOME screen, single-clickthe IFC knob and rotate the IFC knob seven clicks clockwise until the display reads “MENU/P-EQ”. Single-clickthe IFC knob to select the PEQ1 Function or rotate the IFC knob clockwise or counter-clockwiseand single-clickto select PEQ2 FunctionSTA-800D/1000DEquipped Subs Integrated Function ControllerSVSound Integrated Function Controller FIG.8SVSound STA-800D/1000DEquipped SubsSVSound Setup, Calibration & IntegrationUnpacking and Subwoofer Location FIG.9 Power and Signal ConnectionSetup, Calibration & Integration Calibrating the Subwoofer Setup, Calibration & IntegrationSVSound STA-800D/1000DEquipped SubsSetup, Calibration & Integration At the completion of running the auto setup routine, there are two things you should check in your AVR or pre/pro’s Manual Speaker Setup Menu to make sure your subwoofer has been integrated properlySVSound STA-800D/1000DEquipped SubsSetup, Calibration & Integration crossovers set no lower than 80 Hz a speaker set to Small - as opposed to Large or Full Range - will cause bass frequencies below the selected crossover to be routed from the speaker to the subwooferSTA-800D/1000DEquipped Subs Port TuningSVSound Setup & Use of PEQ Advanced Features Parametric Equalizer PEQSetup & Use of PEQ “Q” Control EffectsMeasuring In-RoomFrequency Response Setup & Use of PEQSVSound STA-800D/1000DEquipped SubsSetup & Use of PEQ SVSoundSTA-800D/1000DEquipped Subs To measure the FR of the subwoofer only, connect your sound card output directly to a line level input on the subwoofer. Use the Excel spreadsheet named Subwoofer Frequency Response link provided above, which will plot the frequency response of the subwoofer from 11.2 Hz to 100.8 Hz. Input your raw direct read values from your SPL meter into the green band of frequencies in the Raw SPL Data worksheet, and the Frequency Response worksheet will plot the FR of the subwooferSetup & Use of PEQ Adjusting The PEQ Identify the largest/widest peak in the response and target it for reduction with the PEQ control. When making adjustments to the PEQ control, there is no need to re-plotthe entire FR for interim adjustments - simply re-plotthe affected section of the curve to verify your PEQ adjustments are having the desired effect. When you are done making adjustments, you can re-plotthe entire frequency response to obtain a final curveSVSound STA-800D/1000DEquipped SubsSetup & Use of PEQ Set the Frequency control to the approximate center frequency of the largest peak. Set the Q control to 14.4 narrowest bandwidth, and set the Level control to -6dB. Play the test tones again and re-measureand re- plot the affected portion of the FR curve and visually evaluate your results. Simple trial/error will then allow you to adjust all three controls to shape the PEQ cut to achieve the desired effectAdvanced Features Room Compensation Room CompensationTerms & Conditions SVSound 6420 Belmont Avenue, Girard, Ohio FaxSVSound STA-800D/1000DEquipped Subs