PB13-Ultra, PC13-Ultra, SB13-Ultra
Models PB12-Plus, PC12-Plus, SB13-Plus
Manual Version 1.4 June
Manual Version 1.5 Sep
Table of Contents
Important Safety Instructions
Important Safety Instructions
STA-800D/1000DEquipped Subs
WELCOME
SVSound
About your SVS Subwoofer
Connectivity & Panel Operations
Operation of the Power Mode Switch
Inputs
Input Configuration
Connectivity & Panel Operations
SVSound
STA-800D/1000DEquipped Subs
Connectivity & Panel Operations
SVSound
STA-800D/1000DEquipped Subs
Connectivity & Panel Operations
SVSound
Connectivity & Panel Operations
If you have one of SVS’s AS-EQ1 high-resolution, multi-subwooferEqualizers, see Figure 6 for proper connec- tivity with one or more subwoofers. Also refer to your AS-EQ1Operator Manual for detailed information on connectivity and setup of the AS-EQ1into your listening environment
FIG.
SVSound
Main Power Switch
Power Mode Switch
Power Cord
Outputs
The IFC knob has three actions associated with it
Integrated Function Controller
The two line LCD display has two context modes
1.Top-levelmenu screens
Integrated Function Controller
Volume
High Pass Filter HPF Adjustment STA-1000D
Phase Degree
Low Pass Filter LPF Adjustment
Integrated Function Controller
SVSound
Room Gain Comp
High Pass Delay STA-1000D
Integrated Function Controller
SVSound
P-EQParametric EQualizer
Subwoofer Tune Ported Subwoofers Only
Integrated Function Controller
SVSound
SVSound
Integrated Function Controller
STA-800D/1000DEquipped Subs
From the IFC WELCOME screen, single-clickthe IFC knob and rotate the IFC knob seven clicks clockwise until the display reads “MENU/P-EQ”. Single-clickthe IFC knob to select the PEQ1 Function or rotate the IFC knob clockwise or counter-clockwiseand single-clickto select PEQ2 Function
STA-800D/1000DEquipped Subs
Integrated Function Controller
SVSound
FIG.8
Integrated Function Controller
SVSound
STA-800D/1000DEquipped Subs
SVSound
Setup, Calibration & Integration
Unpacking and Subwoofer Location
FIG.9
Power and Signal Connection
Setup, Calibration & Integration
Setup, Calibration & Integration
Calibrating the Subwoofer
SVSound
STA-800D/1000DEquipped Subs
At the completion of running the auto setup routine, there are two things you should check in your AVR or pre/pro’s Manual Speaker Setup Menu to make sure your subwoofer has been integrated properly
Setup, Calibration & Integration
SVSound
STA-800D/1000DEquipped Subs
crossovers set no lower than 80 Hz a speaker set to Small - as opposed to Large or Full Range - will cause bass frequencies below the selected crossover to be routed from the speaker to the subwoofer
Setup, Calibration & Integration
STA-800D/1000DEquipped Subs
Port Tuning
SVSound
Advanced Features Parametric Equalizer PEQ
Setup & Use of PEQ
“Q” Control Effects
Setup & Use of PEQ
Setup & Use of PEQ
Measuring In-RoomFrequency Response
SVSound
STA-800D/1000DEquipped Subs
SVSound
Setup & Use of PEQ
STA-800D/1000DEquipped Subs
To measure the FR of the subwoofer only, connect your sound card output directly to a line level input on the subwoofer. Use the Excel spreadsheet named Subwoofer Frequency Response link provided above, which will plot the frequency response of the subwoofer from 11.2 Hz to 100.8 Hz. Input your raw direct read values from your SPL meter into the green band of frequencies in the Raw SPL Data worksheet, and the Frequency Response worksheet will plot the FR of the subwoofer
Adjusting The PEQ Identify the largest/widest peak in the response and target it for reduction with the PEQ control. When making adjustments to the PEQ control, there is no need to re-plotthe entire FR for interim adjustments - simply re-plotthe affected section of the curve to verify your PEQ adjustments are having the desired effect. When you are done making adjustments, you can re-plotthe entire frequency response to obtain a final curve
Setup & Use of PEQ
SVSound
STA-800D/1000DEquipped Subs
Set the Frequency control to the approximate center frequency of the largest peak. Set the Q control to 14.4 narrowest bandwidth, and set the Level control to -6dB. Play the test tones again and re-measureand re- plot the affected portion of the FR curve and visually evaluate your results. Simple trial/error will then allow you to adjust all three controls to shape the PEQ cut to achieve the desired effect
Setup & Use of PEQ
Room Compensation
Advanced Features Room Compensation
SVSound 6420 Belmont Avenue, Girard, Ohio Fax
Terms & Conditions
SVSound
STA-800D/1000DEquipped Subs