5 - Messages, troubleshooting, etc.
The following messages may appear on the display under certain circumstances. The meaning of these messages, and any countermeasures which are appro- priate are given here.
Message | Meaning and countermeasure (if | |
appropriate) | ||
| ||
|
| |
|
| |
| The disc has been inserted, and the disc | |
READING | information is being read by the | |
| ||
|
| |
| Optimal Power Calibration is in progress | |
| (a recordable disc has been inserted, and | |
OPC | the | |
| mechanism to match the disc | |
| characteristics.) | |
|
| |
| No disc is loaded into the | |
NO DISC | You may also see this message if you | |
load a disc | ||
| ||
| disc. | |
|
| |
| After recording has finished, the | |
| ||
UPDATE | contents, and displays this message. This | |
is not the same as the permanent table of | ||
| ||
| contents produced by a finalizing | |
| operation. | |
|
| |
WAIT | The | |
operation. | ||
| ||
|
| |
| More than 20 tracks have been | |
FULL | programmed for programmed playback | |
| (see 3.3.1, "Programmed playback"). | |
|
| |
CD FULL | No more space is left for recording on the | |
disc. | ||
| ||
|
| |
| You have tried to finalize an empty disc; it | |
EMPTY | is not possible to write a table of contents | |
| for an empty disc! | |
|
| |
| Sync start has been selected to | |
| synchronize recording with a digital audio | |
INPUT | source (4.2, "Recording from digital | |
| sources") but a digital source has not | |
| been selected as the input. | |
|
| |
| The OPC operation has been carried out | |
FINAL | more than 96 times; this is a warning to | |
| you that the disc must now be finalized. | |
|
| |
| The data on the disc was corrupted, | |
| possibly due to a power failure during a | |
RECOVER | write operation. The | |
| attempting to restore the corrupted data | |
| so that the disc can be used. | |
|
|
Message | Meaning and countermeasure (if | |
appropriate) | ||
| ||
|
| |
|
| |
| The OPC operation has failed when the | |
| disc is inserted. This may be due to the | |
| disc having been inserted more than 99 | |
OPC FAIL | times, or it may be that the disc is dirty. If | |
you know that the disc has not been | ||
| ||
| inserted more than 99 times, clean the | |
| disc using the methods described in 1.1, | |
| "About | |
|
| |
| The | |
| operation. Remove any disc, turn off the | |
SERVICE | ||
it back on again. If this message appears | ||
| ||
| again, contact your TASCAM service | |
| center. | |
|
| |
|
|
5.1 Troubleshooting
In addition to the messages above, here is a list of problems and possible solutions:
Problem | Solution | |
|
| |
|
| |
| Make sure the power cable is connected | |
| to a power socket of the correct voltage. | |
No power | Reset the | |
| power switch off, waiting for a short while, | |
| and switching it on again. | |
|
| |
| Are the correct connections made to the | |
No sound on | amplifying equipment? | |
Is the input selector of the amplifying | ||
replay | ||
equipment switched to the correct | ||
| ||
| source? | |
|
| |
| Are the balanced | |
Distorted sound | connected to a +4 dBu input? | |
Are the trimmers on the balanced | ||
| ||
| ||
|
| |
Sound is too | Are the unbalanced RCA connectors | |
faint | connected to a | |
|
| |
| Is the disc label side upwards and placed | |
Disc does not | correctly in the disc tray? | |
Is the disc clean? | ||
start | ||
Try another disc to see if the problem lies | ||
| ||
| with a particular disc | |
|
| |
Cannot select | Sync start is selected for a digital input | |
manual track | source (4.3, "Automatic track division") | |
division |
| |
|
| |
| The input levels are set too high (analog | |
Recording is | recording) | |
The | ||
distorted | ||
are receiving analog signals from a | ||
| ||
| +4 dBu signal source. | |
|
|
TASCAM