Taylor taylor Section 6 Operating Procedures

18 Models 150, 152, 162, 168Operating Procedures

120501

Section 6 Operating Procedures

The Model 150 has been selected to illustrate the

pictured step- by- step operating procedures. All

models in this manual are similar. They each have a

1.5 quart (1.4 liter) c apacity freezing cylinder. The mix

flows by gravity from the hopper to the freezing

cylinder through an feed tube.

The Model 150 is a console model with a single spout

door.

The Model 152 is a counter model with a single spout

door.

The Model 162 is a counter model and the Model 168

is a console model. Both have three spout doors. Two

individual flavors are available from the end spouts,

andan equal c ombination of both is dispensed through

the center spout to create a twist effect .

For the Models 162 and 168, duplicate the procedures

where they apply for the second freezing cylinder.

We begin our instructions at the point where we enter

the store in the morning and find the parts

disassembled and laid out to air dry from the prev ious

night’s cleaning.

These opening procedures will show you how to

assemble these parts into the freezer, sanitize them,

and prime the freezer with fresh mix in preparation to

serve your first portion.

Figure 11

Figure 12

Figure 13

Figure 14

If you are disassemblingthe machine for the first time

or need information to get to the starting point in our

instructions, turn to page 26, “Disassembly”, and start

there.

Contents

Main Page Table of Contents Table of Contents - Page 2 Section 1 To the Installer Installer Safety S Site Preparation Air Cooled Units Electrical Hook- Up Installation For Electrical Connections For S Beater Rotation Refrigerant Section 2 To the Operator Compressor Warranty Disclaimer Section 3 Safety S S S S 7 Models 150, 152, 162, 168 Operator Parts Identification Section 4 Operator Parts Identification Model 150 Figure 1 8Models 150, 152, 162, 168Operator Parts Identificati on Model 152 Figure 2 9 Models 150, 152, 162, 168 Operator Parts Identification Model 162 Figure 3 10 Models 150, 152, 162, 168Operator Parts Identificati on Model 168 Figure 4 11 Models 150, 152, 162, 168 Operator Parts Identification Models 150 & 152 Door Assembly Figure 5 12 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 & 168 Door Assembly Figure 6 Models 150 and 152 Accessories 14 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 and 168 Accessories Figure 8 Section 5 Important: To the Operator Symbol Definitions Reset Button Power Switch Feed Tube Taylor Quality Control Indicator Light - Mix Low Cylinder Temperature Retention (CTR) Section 6 Operating Procedures Assembly Page Page Sanitizing Page Priming Closing Procedure S S S S S Draining Product From the Freezing Cylinder Rinsing Cleaning Disassembly Brush Cleaning Section 7 Important: Operator Checklist During Cleaning and Sanitizing Troubleshooting Bacterial Count Regular Maintenance Checks Winter Storage Section 8 Troubleshooting Guide Page Page 32 Models 150, 152, 162, 168Parts Replacement Schedule Section 9 Parts Replacement Schedule Section 10 Limited Warranty on Equipment TaylorCompany Section 11 Limited Warranty on Parts Page TaylorCompany Section 12 Parts List Page Page Page Page Page Page Page Page 150/152 050416-12 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. MODEL #152 CONNECT INTERNAL BLUE TO TERMINAL 5 150/152 050416-27 4) THE EQUIPTENTIAL GROUND IS ONLY REQUIRED FOR FIG. 1 VISCOSITY CONTROL TERMINALS: 150/152 050416-40 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FIG. 1 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. 050205-12 BLU/WHT "CCW" ROTATION FIG. 1 FIG. 2 050205-27 REF VISCOSITY CONTROL STR REF VISCOSITY CONTROL BLACK/WHITE STRIPE 050205-40s FIG. 3 FIG. 2 FIG. 1 FIG. 4