Taylor taylor Priming

24 Models 150, 152, 162, 168Operating Procedures

Priming

Prime the machine as close as possible to the time of

first product draw.

Step 1

With a pail beneath the door spout, raise the draw

valve. Fill the mix hopper with fresh mix. (Maximum

hopper capacity is 8 quarts [7.6 liters].) Allow the mix

to flow into the freezing cylinder. This will force out any

remaining sanitizing solution. When full strength m ix is

flowing from the door spout, lower the draw valve.

Note: Use only FRESH mix when priming the

freezer.

Figure 36

Step 2

When the mix has stopped bubbling down into t he

freezing cylinder, install the feed tube in the mix inlet

hole.Mak e sure the small hole in the feed tube is down.

Figure 37

Step 3

Momentarily raise the draw switch paddle to activate

the refrigeration cycle. Place the power switch in the

“AUTO” position. When the unit cycles off, the product

will be ready to serve.

Figure 38

Step 4

Place the mix hopper cover in position.

Repeat Steps 1 through 4 for the second freezing

cylinder on Models 162/168.

Step 5

Install the front drip tray and splash shield under the

freezer door.

Figure 39

Contents

Main Page Table of Contents Table of Contents - Page 2 Section 1 To the Installer Installer Safety S Site Preparation Air Cooled Units Electrical Hook- Up Installation For Electrical Connections For S Beater Rotation Refrigerant Section 2 To the Operator Compressor Warranty Disclaimer Section 3 Safety S S S S 7 Models 150, 152, 162, 168 Operator Parts Identification Section 4 Operator Parts Identification Model 150 Figure 1 8Models 150, 152, 162, 168Operator Parts Identificati on Model 152 Figure 2 9 Models 150, 152, 162, 168 Operator Parts Identification Model 162 Figure 3 10 Models 150, 152, 162, 168Operator Parts Identificati on Model 168 Figure 4 11 Models 150, 152, 162, 168 Operator Parts Identification Models 150 & 152 Door Assembly Figure 5 12 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 & 168 Door Assembly Figure 6 Models 150 and 152 Accessories 14 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 and 168 Accessories Figure 8 Section 5 Important: To the Operator Symbol Definitions Reset Button Power Switch Feed Tube Taylor Quality Control Indicator Light - Mix Low Cylinder Temperature Retention (CTR) Section 6 Operating Procedures Assembly Page Page Sanitizing Page Priming Closing Procedure S S S S S Draining Product From the Freezing Cylinder Rinsing Cleaning Disassembly Brush Cleaning Section 7 Important: Operator Checklist During Cleaning and Sanitizing Troubleshooting Bacterial Count Regular Maintenance Checks Winter Storage Section 8 Troubleshooting Guide Page Page 32 Models 150, 152, 162, 168Parts Replacement Schedule Section 9 Parts Replacement Schedule Section 10 Limited Warranty on Equipment TaylorCompany Section 11 Limited Warranty on Parts Page TaylorCompany Section 12 Parts List Page Page Page Page Page Page Page Page 150/152 050416-12 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. MODEL #152 CONNECT INTERNAL BLUE TO TERMINAL 5 150/152 050416-27 4) THE EQUIPTENTIAL GROUND IS ONLY REQUIRED FOR FIG. 1 VISCOSITY CONTROL TERMINALS: 150/152 050416-40 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FIG. 1 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. 050205-12 BLU/WHT "CCW" ROTATION FIG. 1 FIG. 2 050205-27 REF VISCOSITY CONTROL STR REF VISCOSITY CONTROL BLACK/WHITE STRIPE 050205-40s FIG. 3 FIG. 2 FIG. 1 FIG. 4