Taylor taylor - page 25

Models 150, 152, 162, 168 Operating Procedures

Step 10

Insert the valve lifter arm through the slot tedopening

int he draw valve and align the other end with the cross

holes of the freezer door.

Hint: The valve lifter arm may be aligned wit h the left

or right cross hole. The draw valve handle will be

placed through the opposite cross hole of the valve

lifter arm.

Figure 23

Step 11

Slide the o- ring into the groove on the draw valve

handle and lubricate with Taylor Lube.

Figure 24

Step 12

Insert the draw valve handle through the opposite

cross hole and into the opening of the valve lif ter arm.

Hint: The draw valve handle can be assembled at

varied vertical positions. Choose an angle which is

comfortable for you. The draw valve must be rais ed

completely when the draw valve handle is down.

Figure 25

Note: For Models 162/168, slide the o- ring onto each

pivot pin and lubricate with Taylor Lube.

Figure 26

Contents

Main Page Table of Contents Table of Contents - Page 2 Section 1 To the Installer Installer Safety S Site Preparation Air Cooled Units Electrical Hook- Up Installation For Electrical Connections For S Beater Rotation Refrigerant Section 2 To the Operator Compressor Warranty Disclaimer Section 3 Safety S S S S 7 Models 150, 152, 162, 168 Operator Parts Identification Section 4 Operator Parts Identification Model 150 Figure 1 8Models 150, 152, 162, 168Operator Parts Identificati on Model 152 Figure 2 9 Models 150, 152, 162, 168 Operator Parts Identification Model 162 Figure 3 10 Models 150, 152, 162, 168Operator Parts Identificati on Model 168 Figure 4 11 Models 150, 152, 162, 168 Operator Parts Identification Models 150 & 152 Door Assembly Figure 5 12 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 & 168 Door Assembly Figure 6 Models 150 and 152 Accessories 14 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 and 168 Accessories Figure 8 Section 5 Important: To the Operator Symbol Definitions Reset Button Power Switch Feed Tube Taylor Quality Control Indicator Light - Mix Low Cylinder Temperature Retention (CTR) Section 6 Operating Procedures Assembly Page Page Sanitizing Page Priming Closing Procedure S S S S S Draining Product From the Freezing Cylinder Rinsing Cleaning Disassembly Brush Cleaning Section 7 Important: Operator Checklist During Cleaning and Sanitizing Troubleshooting Bacterial Count Regular Maintenance Checks Winter Storage Section 8 Troubleshooting Guide Page Page 32 Models 150, 152, 162, 168Parts Replacement Schedule Section 9 Parts Replacement Schedule Section 10 Limited Warranty on Equipment TaylorCompany Section 11 Limited Warranty on Parts Page TaylorCompany Section 12 Parts List Page Page Page Page Page Page Page Page 150/152 050416-12 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. MODEL #152 CONNECT INTERNAL BLUE TO TERMINAL 5 150/152 050416-27 4) THE EQUIPTENTIAL GROUND IS ONLY REQUIRED FOR FIG. 1 VISCOSITY CONTROL TERMINALS: 150/152 050416-40 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FIG. 1 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. 050205-12 BLU/WHT "CCW" ROTATION FIG. 1 FIG. 2 050205-27 REF VISCOSITY CONTROL STR REF VISCOSITY CONTROL BLACK/WHITE STRIPE 050205-40s FIG. 3 FIG. 2 FIG. 1 FIG. 4