Taylor taylor - page 24

20 Models 150, 152, 162, 168Operating Procedures

120501

Step 7

Finger- tighten the handscrews, making sure they are

tightened equally and that the door is snug. Do not

over- tighten the handscrews.

IMPORTANT! Handscrew and door damage can

result if the handscrews are over -tightened o r if

one handscrew is tighten ed more than the other.

Step 8

Slide the two o- rings into the grooves on the draw

valve(s) and lubricate with Taylor Lube.

Figure 19

Note: For the Models 162/168, install the valve seal

in the grooves on the center draw valve and lubricate

with Taylor Lube. This special seal will prevent mix

from one freezing cylinder from t raveling into the

second cylinder.

Figure 20

Step 9

Lubricate the inside of the freezer door spout( s) from

the bottom. Insert the draw valve(s) into the freezer

door from the bottom.

Figure 21

Note: The draw valve is installed c orrectly when the

slotted opening in the draw valve is visible through the

“window” of the freezer door.

Figure 22

Contents

Main Page Table of Contents Table of Contents - Page 2 Section 1 To the Installer Installer Safety S Site Preparation Air Cooled Units Electrical Hook- Up Installation For Electrical Connections For S Beater Rotation Refrigerant Section 2 To the Operator Compressor Warranty Disclaimer Section 3 Safety S S S S 7 Models 150, 152, 162, 168 Operator Parts Identification Section 4 Operator Parts Identification Model 150 Figure 1 8Models 150, 152, 162, 168Operator Parts Identificati on Model 152 Figure 2 9 Models 150, 152, 162, 168 Operator Parts Identification Model 162 Figure 3 10 Models 150, 152, 162, 168Operator Parts Identificati on Model 168 Figure 4 11 Models 150, 152, 162, 168 Operator Parts Identification Models 150 & 152 Door Assembly Figure 5 12 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 & 168 Door Assembly Figure 6 Models 150 and 152 Accessories 14 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 and 168 Accessories Figure 8 Section 5 Important: To the Operator Symbol Definitions Reset Button Power Switch Feed Tube Taylor Quality Control Indicator Light - Mix Low Cylinder Temperature Retention (CTR) Section 6 Operating Procedures Assembly Page Page Sanitizing Page Priming Closing Procedure S S S S S Draining Product From the Freezing Cylinder Rinsing Cleaning Disassembly Brush Cleaning Section 7 Important: Operator Checklist During Cleaning and Sanitizing Troubleshooting Bacterial Count Regular Maintenance Checks Winter Storage Section 8 Troubleshooting Guide Page Page 32 Models 150, 152, 162, 168Parts Replacement Schedule Section 9 Parts Replacement Schedule Section 10 Limited Warranty on Equipment TaylorCompany Section 11 Limited Warranty on Parts Page TaylorCompany Section 12 Parts List Page Page Page Page Page Page Page Page 150/152 050416-12 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. MODEL #152 CONNECT INTERNAL BLUE TO TERMINAL 5 150/152 050416-27 4) THE EQUIPTENTIAL GROUND IS ONLY REQUIRED FOR FIG. 1 VISCOSITY CONTROL TERMINALS: 150/152 050416-40 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FIG. 1 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. 050205-12 BLU/WHT "CCW" ROTATION FIG. 1 FIG. 2 050205-27 REF VISCOSITY CONTROL STR REF VISCOSITY CONTROL BLACK/WHITE STRIPE 050205-40s FIG. 3 FIG. 2 FIG. 1 FIG. 4