Taylor taylor Assembly

19

Models 150, 152, 162, 168 Operating Procedures

120501

Assembly

Note: When lubricating parts, use an approved f ood

grade lubricant (example: Taylor Lube).

Step 1

Lubricate the groove on the beater drive shaft. W itht he

opening of the cup seal facing away from t he hex end,

slide the seal into the groove. Apply an even coat of

lubricant to the seal and the shaft. Do not

lubricate the hexend of the beater drive shaft.

Figure 15

Step 2

Insert the beater assembly through the rear shell

bearingat t he back of the freezing cylinder and engage

the hex end firmly into the female socket. When

properly seated, the beater will not protrude beyond

the front of the freezing cylinder.

Figure 16

Repeat this step for the second freezing cylinder on

Models 162/168.

Step 3

Placet he large o- ring(s) into the groove(s ) on the back

of the freezer door and lubricate with Taylor Lube.

Figure 17

Step 4

Slide the front bearing(s) over the baffle rod(s) so the

flanged edge is against the door. Place the white

plastic guide bearing(s) on the end of the baffle rod(s).

Do not lubricate the front bearing(s)or the guide

bearing(s).

Figure 18

Step 5

Slide the slotted portion of the handscrews into the

slots in the freezer door.

Step 6

With both hands, hold the sides of the freezer door and

insert the baffle rod(s) into the center of the beat er

assembly(ies). The white guide bearing(s) must fit

securely in the hole(s) of the drive shaft(s).

Contents

Main Page Table of Contents Table of Contents - Page 2 Section 1 To the Installer Installer Safety S Site Preparation Air Cooled Units Electrical Hook- Up Installation For Electrical Connections For S Beater Rotation Refrigerant Section 2 To the Operator Compressor Warranty Disclaimer Section 3 Safety S S S S 7 Models 150, 152, 162, 168 Operator Parts Identification Section 4 Operator Parts Identification Model 150 Figure 1 8Models 150, 152, 162, 168Operator Parts Identificati on Model 152 Figure 2 9 Models 150, 152, 162, 168 Operator Parts Identification Model 162 Figure 3 10 Models 150, 152, 162, 168Operator Parts Identificati on Model 168 Figure 4 11 Models 150, 152, 162, 168 Operator Parts Identification Models 150 & 152 Door Assembly Figure 5 12 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 & 168 Door Assembly Figure 6 Models 150 and 152 Accessories 14 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 and 168 Accessories Figure 8 Section 5 Important: To the Operator Symbol Definitions Reset Button Power Switch Feed Tube Taylor Quality Control Indicator Light - Mix Low Cylinder Temperature Retention (CTR) Section 6 Operating Procedures Assembly Page Page Sanitizing Page Priming Closing Procedure S S S S S Draining Product From the Freezing Cylinder Rinsing Cleaning Disassembly Brush Cleaning Section 7 Important: Operator Checklist During Cleaning and Sanitizing Troubleshooting Bacterial Count Regular Maintenance Checks Winter Storage Section 8 Troubleshooting Guide Page Page 32 Models 150, 152, 162, 168Parts Replacement Schedule Section 9 Parts Replacement Schedule Section 10 Limited Warranty on Equipment TaylorCompany Section 11 Limited Warranty on Parts Page TaylorCompany Section 12 Parts List Page Page Page Page Page Page Page Page 150/152 050416-12 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. MODEL #152 CONNECT INTERNAL BLUE TO TERMINAL 5 150/152 050416-27 4) THE EQUIPTENTIAL GROUND IS ONLY REQUIRED FOR FIG. 1 VISCOSITY CONTROL TERMINALS: 150/152 050416-40 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FIG. 1 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. 050205-12 BLU/WHT "CCW" ROTATION FIG. 1 FIG. 2 050205-27 REF VISCOSITY CONTROL STR REF VISCOSITY CONTROL BLACK/WHITE STRIPE 050205-40s FIG. 3 FIG. 2 FIG. 1 FIG. 4