Taylor taylor Winter Storage

28 Models 150, 152, 162, 168Important: OperatorChecklist

j5. If your machine is air cooled, check the

condenser for an accumulation of dirt and lint.

A dirty condenser will reduce the efficiency and

capacity of the machine. Condensers should be

cleaned monthly with a soft brush. Never use

screwdrivers or other metal probes to clean

between the fins. Failure to comply may result

in electrocution.

Note: For machines equipped with an air filter,

it will be necessary to vacuum clean the filters

on a monthly schedule.

j6. On the auxiliary refrigeration system, check the

condenser for accumulation of dirt and lint. A

dirty condenser will reduce the refriger ation

capacity of the mix hopper. Condensers must

be cleaned monthly with a soft brush. Never

use screwdrivers or other metal probes toclean

between the fins. Failure to comply may result

in electrocution.

Winter Storage

If the place of business is to be closed during t he winter

months, it is important to protect the freezer by

following certain precautions, particularly if the

building is subject to freezing conditions.

Disconnect the freezer from the main power source to

prevent possible electrical damage.

Yourlocal Taylordistr ibutor can perform this service for

you.

Wrap detachable parts of the freezer such as the

beater assembly and freezer door, and place them in

a protected dry place. Rubber trim parts and gas kets

can be protected by wrapping them with

moisture- proof paper. All parts should be thoroughly

cleaned of dried mix or lubrication accumulations

which attract mice and other vermin.

Contents

Main Page Table of Contents Table of Contents - Page 2 Section 1 To the Installer Installer Safety S Site Preparation Air Cooled Units Electrical Hook- Up Installation For Electrical Connections For S Beater Rotation Refrigerant Section 2 To the Operator Compressor Warranty Disclaimer Section 3 Safety S S S S 7 Models 150, 152, 162, 168 Operator Parts Identification Section 4 Operator Parts Identification Model 150 Figure 1 8Models 150, 152, 162, 168Operator Parts Identificati on Model 152 Figure 2 9 Models 150, 152, 162, 168 Operator Parts Identification Model 162 Figure 3 10 Models 150, 152, 162, 168Operator Parts Identificati on Model 168 Figure 4 11 Models 150, 152, 162, 168 Operator Parts Identification Models 150 & 152 Door Assembly Figure 5 12 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 & 168 Door Assembly Figure 6 Models 150 and 152 Accessories 14 Models 150, 152, 162, 168Operator Parts Identificati on Models 162 and 168 Accessories Figure 8 Section 5 Important: To the Operator Symbol Definitions Reset Button Power Switch Feed Tube Taylor Quality Control Indicator Light - Mix Low Cylinder Temperature Retention (CTR) Section 6 Operating Procedures Assembly Page Page Sanitizing Page Priming Closing Procedure S S S S S Draining Product From the Freezing Cylinder Rinsing Cleaning Disassembly Brush Cleaning Section 7 Important: Operator Checklist During Cleaning and Sanitizing Troubleshooting Bacterial Count Regular Maintenance Checks Winter Storage Section 8 Troubleshooting Guide Page Page 32 Models 150, 152, 162, 168Parts Replacement Schedule Section 9 Parts Replacement Schedule Section 10 Limited Warranty on Equipment TaylorCompany Section 11 Limited Warranty on Parts Page TaylorCompany Section 12 Parts List Page Page Page Page Page Page Page Page 150/152 050416-12 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. MODEL #152 CONNECT INTERNAL BLUE TO TERMINAL 5 150/152 050416-27 4) THE EQUIPTENTIAL GROUND IS ONLY REQUIRED FOR FIG. 1 VISCOSITY CONTROL TERMINALS: 150/152 050416-40 MODEL #150 CONNECT INTERNAL YELLOW TO TERMINAL 5 FIG. 1 FOR "CW" ROTATION OF GE/RBC BEATER MOTOR FOR AND INTERNAL YELLOW TO TERMINAL 2. 050205-12 BLU/WHT "CCW" ROTATION FIG. 1 FIG. 2 050205-27 REF VISCOSITY CONTROL STR REF VISCOSITY CONTROL BLACK/WHITE STRIPE 050205-40s FIG. 3 FIG. 2 FIG. 1 FIG. 4