Manuals / Brands / Photography / Photo Scanner / Teledyne / Photography / Photo Scanner

Teledyne 703E 6.12.3. LEVELS , 6.12.4. ACTIVATING AN EXISTING LEVEL

1 283

Download 283 pages, 8.19 Mb

TELEDYNE API

Operating the M703E Calibrator M703E Calibrator Operator’s Manual

6.12.3. LEVELS

A LEVEL is a combination of several parameters:

 An ID number for the LEVEL

 An action, (e.g. GENERATE, STANDBY)

 A target concentration value

 An output flow rate (if applicable)

 Configuration for one or both of two status output blocks.

Up to twenty levels can be defined and used with the M703E using a range of ID numbers from 0-98. Level 99

is reserved for standby. Are not time based and do not include characteristics such as start time or duration,

therefore a single LEVEL can not switch between different concentration levels and flow rates. Separate flow

and concentration outputs must be programmed into separate LEVELs which are then individually started and

stopped either by an operator at the calibrator’s front panel or through a serial data operation over the RS-232 or

Ethernet ports.

6.12.4. ACTIVATING AN EXISTING LEVEL

To activate an existing defined LEVEL, press:

80 05744 Rev B

Contents

Main MODEL 703E PHOTOMETRIC O3 CALIBRATOR Page Page Page SAFETY MESSAGES Page Page Page Page Page Page LIST OF FIGURES LIST OF TABLES Page LIST OF APPENDICES Page Page Page 1. INTRODUCTION 1.1. M703E CALIBRATOR OVERVIEW 1.2. USING THIS MANUAL TABLE OF CONTENTS: SECTION I GENERAL INFORMATION SECTION II OPERATING INSTRUCTIONS SECTION III TECHNICAL INFORMATION 2. SPECIFICATIONS, APPROVALS AND WARRANTY 2.1. SPECIFICATIONS 2.2. CE MARK COMPLIANCE 2.3. WARRANTY Page 3. GETTING STARTED 3.1. UNPACKING AND INITIAL SETUP 3.1.1. MODEL 703E CALIBRATOR TELEDYNE API M703E Calibrator Operators Manual Getting Started PHOTOMETER Figure 3-3: M703E Internal Layout Top View 05744 Rev B 11 Page 3.2. ELECTRICAL CONNECTIONS 3.2.1. POWER CONNECTION CAUTION 3.2.2. ANALOG OUTPUT TEST CHANNEL CONNECTIONS + 3.2.3. CONNECTING THE STATUS OUTPUTS 3.2.4. CONNECTING THE CONTROL INPUTS - + 3.2.5. CONNECTING THE CONTROL OUTPUTS CONTROL OUTPUTS 1 2 3 4 5 6 7 8 9 10 11 12 E 3.2.6. CONNECTING THE SERIAL PORTS 3.2.7. CONNECTING TO A LAN OR THE INTERNET 3.2.8. CONNECTING TO A MULTIDROP NETWORK 3.3. PNENUMATIC CONNECTIONS 3.3.1. DRY AIR IN 3.3.2. ZERO AIR IN USER NOTES 3.4. INITIAL OPERATION 3.4.1. START-UP 3.4.2. WARM UP 3.4.3. WARNING MESSAGES MESSAGE MEANING 05744 Rev B 23 3.4.4. FUNCTIONAL CHECK messages are active. more calibration sequences are programmed into the calibrators memory. 3.4.5. OPERATING MODES FOR THE O3 GENERATOR 3.4.5.1. CNST (CONSTANT) 3.4.5.2. REF (REFERENCE) 3.4.5.3. BNCH (BENCH) 3.4.6. SETTING THE O3 GENERATOR MODE 3.4.7. SETTING THE M703ES OUTPUT FLOW RATE 4. FREQUENTLY ASKED QUESTIONS AND GLOSSARY 4.1. FAQS 4.2. GLOSSARY Page 5. OPTIONAL HARDWARE AND SOFTWARE 5.1. CARRYING STRAP HANDLE (OPT 29) 5.2. COMMUNICATION OPTIONS 5.2.1. RS232 MODEM CABLES (OPTS 60 AND 60A) 5.2.2. ETHERNET CABLE (OPT 60B) 5.2.3. RS-232 MULTIDROP (OPT 62) 5.2.4. ETHERNET (OPT 63) 5.2.5. ETHERNET + MULTIDROP (OPT 64) 5.3. ADDITIONAL MANUAL (OPT 70) 5.4. EXTENDED WARRANTY (OPT 92) 5.5. NIST TRACEABLE, PRIMARY STANDARD CERTIFICATION Page Page 6. OPERATING THE M703E CALIBRATOR 6.1. TEST FUNCTIONS TEST MEASUREMENT DESCRIPTION 6.2. OVERVIEW OF OPERATING MODES Mode Field STANDBY Key MODE MEANING 6.3. STANDBY MODE 6.4. GENERAL INFORMATION ABOUT THE GENERATE MODE 6.4.1. GENERATE AUTO: Basic Generation of Calibration Gas 6.5. AUTOMATIC CALIBRATION SEQUENCES 6.5.1. SETUP SEQ: PROGRAMMING CALIBRATION SEQUENCES 40 05744 Rev B Table 6-3: Automatic Calibration SEQUENCE Set Up Attributes ATTRIBUTE NAME DESCRIPTION Page TELEDYNE API Operating the M703E Calibrator M703E Calibrator Operators Manual 6.5.1.2. Naming a Sequence 42 05744 Rev B TELEDYNE API M703E Calibrator Operators Manual Operating the M703E Calibrator 6.5.1.3. Setting the Repeat Count for a Sequence 05744 Rev B 43 Page 05744 Rev B 45 DAY MONTH YEAR HOUR MINUTE 46 05744 Rev B HOUR MINUTE 6.5.1.5. Setting Up Control Inputs for a Sequence 05744 Rev B 47 6.5.1.6. Setting Up Control Outputs for a Sequence 48 05744 Rev B TELEDYNE API M703E Calibrator Operators Manual Operating the M703E Calibrator 6.5.1.7. Setting the PROGRESS Reporting Mode for the Sequences REM 05744 Rev B 49 ELAP Table 6-5: Sequence Progress Reporting Mode Page TELEDYNE API M703E Calibrator Operators Manual Operating the M703E Calibrator 6.5.2.1. The Generate Step 05744 Rev B 51 6.5.2.2. The STANDBY Step 6.5.2.3. The DURATION Step 6.5.2.4. The EXECSEQ Step TELEDYNE API Operating the M703E Calibrator M703E Calibrator Operators Manual 6.5.2.5. The CC OUTPUT Step 54 05744 Rev B Toggle this key turn the CC input ON/OFF Page 6.5.3. DELETING A SEQUENCE 6.6. SETUP CFG 05744 Rev B 57 TELEDYNE API Operating the M703E Calibrator M703E Calibrator Operators Manual 58 05744 Rev B 6.7. SETUP CLK 6.7.1. SETTING THE INTERNAL CLOCKS TIME AND DAY EXIT returns to SETUP X.X display HOUR MINUTE DAY MONTH YEAR Page 6.8. SETUP PASS Page 6.9. SETUP DIAG TEST CHAN OUTPUT: USING THE TEST CHANNEL ANALOG OUTPUT + 62 05744 Rev B Figure 6-2: M703E the TEST CHANNEL Connector 6.9.1. CONFIGURING THE TEST CHANNEL ANALOG OUTPUT Not used in the M703E 05744 Rev B 63 TELEDYNE API Operating the M703E Calibrator M703E Calibrator Operators Manual 6.9.1.2. Selecting a Test Channel Function to Output The Test Functions available to be reported are: 64 05744 Rev B Table 6-8: Test Channels Functions Available on the M703Es Analog Output TEST setting ENTR accepts the new setting 6.9.1.3. TEST CHANNEL VOLTAGE RANGE Configuration Table 6-9: Analog Output Voltage Range Min/Max RANGE SPAN MINIMUM OUTPUT MAXIMUM OUTPUT 66 05744 Rev B Page Page 6.9.2. TEST CHANNEL CALIBRATION TEST CHANNEL 05744 Rev B 69 CHANNEL can be initiated with the AOUTS CALIBRATION command. 6.9.2.1. Enabling or disabling the TEST CHANNEL Auto-Cal Feature 6.9.2.2. Automatic TEST CHANNEL Calibration Page 6.9.2.3. Manual Calibration of the TEST CHANNEL configured for Voltage Ranges TELEDYNE API M703E Calibrator Operators Manual Operating the M703E Calibrator 05744 Rev B 73 To adjust the signal levels of an analog output channel manually, press: These menus only appear if AUTO-CAL is turned OFF 6.9.3. AIN CALIBRATION TELEDYNE API M703E Calibrator Operators Manual Operating the M703E Calibrator 6.10. SETUP MORE VARS: INTERNAL VARIABLES (VARS) 05744 Rev B 75 7 4 3 TELEDYNE API Operating the M703E Calibrator M703E Calibrator Operators Manual 76 05744 Rev B To access and navigate the VARS menu, use the following key sequence: In all cases: EXIT discards the new setting ENTR accepts the new setting 6.11. OPERATING THE M703E CALIBRATOR AS AN O3 PHOTOMETER 6.11.1. SET UP FOR OPERATING THE M703E AS AN O3 PHOTOMETER 1 M703E Photometric O3 Calibrator REFERENCE GAS SOURCE Page 6.12. SETUP LVL: SETTING UP AND USING LEADS (DASIBI) OPERATING LEVELS 6.12.1. GENERAL INFORMATION ABOUT LEADS LEVELS 05744 Rev B 79 NOTE For more information on the LEADS system, please go to http://www.meteostar.com/. 6.12.2. DOT COMMANDS 6.12.3. LEVELS 6.12.4. ACTIVATING AN EXISTING LEVEL 80 05744 Rev B 05744 Rev B 81 6.12.5. PROGRAMMING NEW LEVELS TELEDYNE API Operating the M703E Calibrator M703E Calibrator Operators Manual 6.12.5.1. Creating a GENERATE LEVEL To create a LEVEL using the M703Es AUTO generation function, press: 82 05744 Rev B TELEDYNE API M703E Calibrator Operators Manual Operating the M703E Calibrator 6.12.5.2. Creating a MANUAL LEVEL To create a level using the M703Es MANUAL generation function, press: 6.12.5.3. Editing or Deleting a LEVEL 84 05744 Rev B Page TELEDYNE API Operating the M703E Calibrator M703E Calibrator Operators Manual 6.12.6. CONFIGURING LEVEL STATUS BLOCKS 86 05744 Rev B Toggle this key turn the CC input ON/OFF 7. OPERATING THE M703E OVER THE SERIAL I/O PORTS 05744 Rev B 87 7.1. USING THE ANALYSERS COMMUNICATION PORTS 7.1.1. RS-232 DTE AND DCE COMMUNICATION TELEDYNE API Operating The M703E over the Serial I/O Ports M703E Calibrator Operators Manual 7.1.2. COMM PORT DEFAULT SETTINGS AND CONNECTOR PIN ASSIGNMENTS RXD RTS TXD GND (As seen from inside analyzer) RXD GND Page 7.1.3. COMM PORT BAUD RATE TELEDYNE API M703E Calibrator Operators Manual Operating The M703E over the Serial I/O Ports 7.1.4. COMM PORT COMMUNICATION MODES Table 7-1: COMM Port Communication Modes MODE1 ID DESCRIPTION Note Communication Modes for each COM port must be configured independently. 05744 Rev B 91 Page 7.1.5. COMM PORT TESTING 94 05744 Rev B 7.1.6. MACHINE ID 7.1.7. TERMINAL OPERATING MODES 7.1.7.1. Help Commands in Terminal Mode 05744 Rev B 95 Table 7-2: Terminal Mode Software Commands 7.1.7.2. Command Syntax Table 7-3: Teledyne Instruments Serial I/O Command Types 96 05744 Rev B 7.1.7.3. Data Types 7.1.7.4. Status Reporting 05744 Rev B 97 7.1.7.5. COM Port Password Security 98 05744 Rev B 7.2. REMOTE ACCESS BY MODEM MODEM ENABLE 05744 Rev B 99 AT Y0 &D0 &H0 &I0 S0=2 &B0 &N6 &M0 E0 Q1 &W0 If there is a problem initializing the modem the message, MODEM NOT INITIALIZED will appear. Continue pressing <SET or SET> until ... Test Runs Automatically 7.3. MULTIDROP RS-232 SET UP Rear Panel 05744 Rev B 101 PCA CALIBRATOR CALIBRATOR TAPI Analyzer 102 05744 Rev B INSTRUMENT Host RS-232 port Figure 7-4: RS232-Multidrop PCA Host/Calibrator Interconnect Diagram 7.4. RS-485 CONFIGURATION OF COM2 Figure 7-6: Back Panel connector Pin-Outs for COM2 in RS-485 mode. Figure 7-7: CPU connector Pin-Outs for COM2 in RS-485 mode. 104 05744 Rev B 7.5. REMOTE ACCESS VIA THE ETHERNET 7.5.1. ETHERNET CARD COM2 COMMUNICATION MODES AND BAUD RATE 7.5.2. CONFIGURING THE ETHERNET INTERFACE OPTION USING DHCP Page Page 7.5.2.1. Manually Configuring the Network IP Addresses 108 05744 Rev B 05744 Rev B 109 From Step 1 above) Contact your IT Network Administrator TELEDYNE API Operating The M703E over the Serial I/O Ports M703E Calibrator Operators Manual 7.5.3. CHANGING THE CALIBRATORS HOSTNAME Contact your IT Network Administrator the new setting EXIT ignores the new setting 7.6. APICOM REMOTE CONTROL PROGRAM Page 8. M703E CALIBRATION AND VERIFICATION 8.1. VERIFYING AND CALIBRATING THE M703ES O3 PHOTOMETER 05744 Rev B 113 8.1.1. SETUP FOR VERIFYING AND CALIBRATING THE O3 PHOTOMETER Note This operation requires an external reference photometer. 8.1.1.1. Calibration Manifold Exhaust/Vent Line 8.1.2. VERIFYING O3 PHOTOMETER PERFORMANCE 8.1.3. CALIBRATING THE O3 PHOTOMETER 8.1.3.1. Photometer Zero Calibration Page 8.1.4. O3 PHOTOMETER DARK CALIBRATION Yes No 8.2. CALIBRATING THE O3 GENERATOR 8.2.1. O3 GENERATOR CALIBRATION TABLE 05744 Rev B 119 TELEDYNE API M703E Calibration and Verification M703E Calibrator Operators Manual 8.2.2. VIEWING O3 GENERATOR CALIBRATION POINTS To view these calibration points, press: 120 05744 Rev B Page Page TELEDYNE API M703E Calibrator Operators Manual M703E Calibration and Verification 8.2.5. TURNING O3 GENERATOR CALIBRATION POINTS ON / OFF To enable or disable an existing calibration point, press: 05744 Rev B 123 EXIT discards the new setting ENTR accepts the new setting Page TELEDYNE API M703E Calibrator Operators Manual M703E Calibration and Verification 8.3. M703E GAS PRESSURE SENSOR CALIBRATION PUMP 05744 Rev B 125 PUMP On Back Panel Page Page 8.4. M703E GAS FLOW CALIBRATION 8.4.1. CALIBRATING THE PHOTOMETERS SAMPLE GAS FLOW 8.4.2. CALIBRATING THE OUTPUT GAS FLOW 8.4.2.1. Output Gas Flow Set Up 130 05744 Rev B Figure 8-5: Output Flow Calibration Monitor Point TELEDYNE API M703E Calibrator Operators Manual M703E Calibration and Verification 8.4.2.2. Performing an Output Gas Flow Calibration 05744 Rev B 131 An external flow meter is needed to perform this operation. EXIT discards the new setting ENTR accepts the new setting Page Page Page 9. THEORY OF OPERATION 9.1. PNEUMATIC OPERATION 05744 Rev B 135 9.1.1. GAS FLOW CONTROL 9.1.1.1. Flow Control Assemblies 9.1.2. INTERNAL GAS PRESSURE SENSORS 136 05744 Rev B TELEDYNE API M703E Calibrator Operators Manual Theory of Operation 9.2. ELECTRONIC OPERATION 9.2.1. OVERVIEW 05744 Rev B 137 I2C Bus 9.2.2. CPU Figure 9-3: M703E CPU Board Annotated 138 05744 Rev B 9.2.2.1. Disk On Chip 9.2.2.2. Flash Chip 05744 Rev B 139 9.2.3. RELAY PCA Figure 9-4: Relay Board PCA with AC Relay Retainer Removed 140 05744 Rev B 9.2.3.1. Valve Control 9.2.3.2. Heater Control Figure 9-5: Heater Control Loop Block Diagram. 9.2.3.3. Relay PCA Status LEDs & Watch Dog Circuitry Figure 9-6: Status LED Locations Relay PCA 05744 Rev B 141 9.2.3.4. Relay PCA Watchdog Indicator (D1) 142 05744 Rev B 9.2.4. MOTHERBOARD 9.2.4.1. A to D Conversion 05744 Rev B 143 9.2.4.2. Sensor Inputs 9.2.4.3. Thermistor Interface 9.2.4.5. External Digital I/O CONC VALID 144 05744 Rev B 9.2.4.6. I2C Data Bus 9.2.4.7. Power-up Circuit 9.2.5. POWER SUPPLY AND CIRCUIT BREAKER 05744 Rev B 145 RELAY PCA 9.2.6. AC POWER CONFIGURATION 9.2.6.1. AC configuration Internal Pump (JP7) 9.3. FRONT PANEL INTERFACE 9.3.1.1. Calibrator Status LEDs Table 9-3: Front Panel Status LEDs 148 05744 Rev B 9.3.1.2. Keyboard 9.3.1.3. Display 9.3.1.4. Keyboard/Display Interface Electronics Figure 9-11: Keyboard and Display Interface Block Diagram 05744 Rev B 149 KEYPAD DECODER KEY-PRESS DETECT CIRCUIT 9.4. SOFTWARE OPERATION Figure 9-12: Schematic of Basic Software Operation 150 05744 Rev B 9.5. O3 GENERATOR OPERATION 9.5.1. PRINCIPLE OF PHOTOLYTIC O3 GENERATION Figure 9-13: O3 Generator Internal Pneumatics 05744 Rev B 151 9.5.2. GENERATOR PNEUMATIC OPERATION Figure 9-14: O3 Generator Valve and Gas Fixture Locations 152 05744 Rev B 9.5.3. O3 GENERATOR ELECTRONIC OPERATION O3 Generator Figure 9-15: O3 Generator Electronic Block Diagram Figure 9-16: O3 Generator Electronic Components Location 05744 Rev B 153 9.5.3.1. O3 Generator Temperature Control 9.6. PHOTOMETER OPERATION I I 05744 Rev B 155 9.6.1. MEASUREMENT METHOD = L 9.6.1.1. Calculating O3 Concentration T P Equation 9-8 inHg92.29 273 L 10 I Figure 9-18: O3 Photometer Gas Flow Measure Cycle O3GEN / PHOTOMETER PRESSURE / FLOW SENSOR PCA Flow Control blk blu 9.6.1.3. The Absorption Path Figure 9-20: O3 Photometer Absorption Path 158 05744 Rev B 9.6.1.4. Interferent Rejection 9.6.2. PHOTOMETER LAYOUT Figure 9-21: O3 Photometer Layout Top Cover Removed 05744 Rev B 159 9.6.3. PHOTOMETER PNEUMATIC OPERATION 9.6.4. PHOTOMETER ELECTRONIC OPERATION MOTHER BOARD I2C Bus PC 104 CPU Card Figure 9-22: O3 Photometer Electronic Block Diagram 9.6.4.1. O3 Photometer Temperature Control 9.6.4.2. Pneumatic Sensors for the O3 Photometer Page 10. MAINTENANCE SCHEDULE & PROCEDURES 10.1. MAINTENANCE SCHEDULE Page ONLY CLEAN, DRY, PARTICULATE FREE Zero Air (Diluent Gas Page 10.2. PERFORMING LEAK CHECKS 10.2.1. PRESSURE LEAK CHECK Flow Control CAP CAP CAP Flow Control Figure 10-1: Pneumatic setup for performing Pressure Leak Checks -END OF INSERTION 168 05744 Rev B Page TELEDYNE API Maintenance Schedule & Procedures M703E Calibrator Operators Manual CAP CAP CAP orn orn (1.0 to 2.0 LPM) Flow Control 10.3. CLEANING OR REPLACING THE ABSORPTION TUBE 10.4. REBUILDING THE DRY AIR PUMP 10.5. PHOTOMETER UV SOURCE LAMP ADJUSTMENT 172 05744 Rev B 10.6. PHOTOMETER UV SOURCE LAMP REPLACEMENT 10.7. ADJUSTMENT OR REPLACEMENT OF OZONE GENERATOR UV LAMP 05744 Rev B 175 Page 11. GENERAL TROUBLESHOOTING & REPAIR OF THE M703E CALIBRATOR 11.1. GENERAL TROUBLESHOOTING 11.1.1. FAULT DIAGNOSIS WITH WARNING MESSAGES 178 05744 Rev B Table 11-1: Front Panel Warning Messages REAR BOARD NOT DET 05744 Rev B 179 WARNING FAULT CONDITION POSSIBLE CAUSES DATA INITIA LIZED O3 GEN LAMP TEMP WA RN IN G O3 GEN REFERENCE WA RN IN G PHOTO LAMP TEMP WA RN IN G 11.1.2. FAULT DIAGNOSIS WITH TEST FUNCTIONS 05744 Rev B 181 11.1.3. USING THE DIAGNOSTIC SIGNAL I/O FUNCTION Figure 11-1: Example of Signal I/O Function 182 05744 Rev B 11.2. USING THE ANALOG OUTPUT TEST CHANNEL 05744 Rev B 183 Table 11-3: Test Channel Outputs as Diagnostic Tools TEST CHANNEL DESCRIPTION ZERO FULL SCALE CAUSES OF EXTREMELY HIGH / LOW READINGS 11.3. USING THE INTERNAL ELECTRONIC STATUS LEDS 11.3.1. CPU STATUS INDICATOR 184 05744 Rev B Mother Board P/N 04069 Figure 11-2: CPU Status Indicator 11.3.2.2. O3 Status LEDs D2 (Yellow) Dry (zero) Air Pump Status 05744 Rev B 185 O3-PUMP-ON PHOTO_REF_VALVE 11.4. SUBSYSTEM CHECKOUT 11.4.1. VERIFY SUBSYSTEM CALIBRATION 186 05744 Rev B 11.4.2. AC MAIN POWER 11.4.3. DC POWER SUPPLY Figure 11-4: Location of DC Power Test Points on Relay PCA 05744 Rev B 187 Table 11-6: DC Power Test Point and Wiring Color Codes Table 11-7: DC Power Supply Acceptable Levels 11.4.4. I2C BUS 188 05744 Rev B 11.4.5. KEYBOARD/DISPLAY INTERFACE 11.4.6. RELAY PCA 11.4.7. PHOTOMETER O3 GENERATOR PRESSURE /FLOW SENSOR ASSEMBLY PHOTOMETER PRESSURE SENSOR: O3 GENERATOR PRESSURE SENSOR 190 05744 Rev B PHOTOMETER FLOW SENSOR 11.4.8. MOTHERBOARD 11.4.8.1. A/D Functions 05744 Rev B 191 PHOTO_FLOW 11.4.8.2. Test Channel / Analog Outputs Voltage 11.4.8.3. Status Outputs 192 05744 Rev B DIAG SIGNAL I/O menu (See Section11.1.3), scroll through the inputs and outputs until Table 11-10: Status Outputs Check PIN (LEFT TO RIGHT) STATUS 11.4.8.4. Control Inputs 11.4.8.5. Control Outputs Table 11-12: Control Outputs Pin Assignments and Corresponding Signal I/O Functions Check 194 05744 Rev B DIAG SIGNAL I/O menu (See Section11.1.3), scroll through the inputs and outputs until 11.4.9. CPU 11.4.10. RS-232 COMMUNICATIONS 11.4.10.1. General RS-232 Troubleshooting 05744 Rev B 195 11.4.10.2. Troubleshooting Calibrator/Modem or Terminal Operation 11.4.11. TEMPERATURE PROBLEMS 11.4.11.1. Box / Chassis Temperature 196 05744 Rev B 11.4.11.2. Photometer Sample Chamber Temperature 11.4.11.3. UV Lamp Temperature 11.5. TROUBLESHOOTING THE O3 PHOTOMETER 11.5.1. DYNAMIC PROBLEMS WITH THE O3 PHOTOMETER 11.5.1.1. Noisy or Unstable O3 Readings at Zero 11.5.1.2. Noisy, Unstable, or Non-Linear Span O3 Readings 11.5.1.3. Slow Response to Changes in Concentration 198 05744 Rev B 11.5.1.4. The Analog Output Signal Level Does Not Agree With Front Panel Readings 11.5.1.5. Cannot Zero 11.5.2. CHECKING MEASURE / REFERENCE VALVE 11.6. TROUBLESHOOTING THE O3 GENERATOR 11.6.1. CHECKING THE UV LAMP POWER SUPPLY 200 05744 Rev B NOTE A schematic and physical diagram of the Lamp Power Supply can be found in Appendix D. WARNING Hazardous voltage present - use caution. 11.7. TROUBLE SHOOTING THE OPTIONAL O3 GENERATOR 11.7.1. CHECKING THE UV SOURCE LAMP POWER SUPPLY 05744 Rev B 201 NOTE A schematic and physical diagram of the Lamp Power Supply can be found in Appendix D. WARNING Hazardous voltage present - use caution. 11.8. REPAIR PROCEDURES 11.8.1. REPAIRING SAMPLE FLOW CONTROL ASSEMBLY 202 05744 Rev B Figure 11-5: Critical Flow Restrictor Assembly Disassembly 11.8.2. DISK-ON-CHIP REPLACEMENT PROCEDURE 11.9. TECHNICAL ASSISTANCE TELEDYNE-API, CUSTOMER SERVICE, Page 12. A PRIMER ON ELECTRO-STATIC DISCHARGE 12.1. HOW STATIC CHARGES ARE CREATED 05744 Rev B 205 Figure 12-1: Triboelectric Charging Table 12-1: Static Generation Voltages for Typical Activities 12.2. HOW ELECTRO-STATIC CHARGES CAUSE DAMAGE Table 12-2: Sensitivity of Electronic Devices to Damage by ESD 206 05744 Rev B 12.3. COMMON MYTHS ABOUT ESD DAMAGE 12.4. BASIC PRINCIPLES OF STATIC CONTROL 12.4.1. GENERAL RULES Figure 12-2: Basic anti-ESD Work Station 05744 Rev B 207 rather than pink-poly bags. bag. 208 05744 Rev B 12.4.2. BASIC ANTI-ESD PROCEDURES FOR ANALYZER REPAIR AND MAINTENANCE 12.4.2.1. Working at the Instrument Rack 05744 Rev B 209 12.4.2.2. Working at an Anti-ESD Work Bench. 12.4.2.3. Transferring Components from Rack to Bench and Back 12.4.2.4. Opening Shipments from Teledyne Instruments Customer Service. 210 05744 Rev B 12.4.2.5. Packing Components for Return to Teledyne Instruments Customer Service. WARNING Page APPENDIX A Version Specific Software Documentation Page Page TELEDYNE API Figure A-2: PRIMARY SETUP MENU - Basics EXITENTR MAIN MENU SETUP O3 PASSCFG CLK MORE ON OFF TIME DATE PREV NEXT Page Page Page TELEDYNE API Figure A-6: SECONDARY SETUP Menu; DIAG Submenu GAS CONFIGURATION A-8 05745 Rev C APPENDIX A-1: Software Menu Trees, Software Version C.0 M703E Calibrator Operators Manual mode. Page Page TELEDYNE API M703E Calibrator Operators M anual 05745 Rev C A-11 TELEDYNE API A-12 05745 Rev C M703E SETUP VARIABLES FOR LATEST REVISION TELEDYNE API M703E Calibrator Operators M anual 05745 Rev C A-13 M703E SETUP VARIABLES FOR LATEST REVISION MODEM_INIT2 BA UD_RA TE 2 TELEDYNE API A-14 05745 Rev C M703E SETUP VARIABLES FOR LATEST REVISION TELEDYNE API M703E Calibrator Operators M anual 05745 Rev C A-15 M703E SETUP VARIABLES FOR LATEST REVISION TELEDYNE API A-16 05745 Rev C TELEDYNE API M703E Calibrator Operators M anual 05745 Rev C A-17 Table A-3: M703E Test Functions, Software Version C.0 Page TELEDYNE API M703E Calibrator Operators M anual 05745 Rev C A-19 Description TELEDYNE API A-20 05745 Rev C M703E I/O Signal List for Latest Revision Signal Name Bit or Channel Number Description Page TELEDYNE API A-22 05745 Rev C Table A-6: Terminal Key Assignments, Software Version C.0 APPENDIX B: Spare Parts List Page Page Spare Parts List Recommended Spare Parts Stocking Levels Units 1 2-5 6-10 11-20 21-30 Part Number Description Page Model M703E Calibrator Operators Manual Warranty/Repair Questionnaire Model 703E PARAMETER RECORDED VALUE ACCEPTABLE VALUE Model M703E Calibrator Operators Manual Warranty/Repair Questionnaire Model 703E Page Page APPENDIX D: Diagrams and Schematics Page Page Page Page + REF_2.5V PHOTO_OUT PCA, UV DETECTOR PREAMP 04420 B 1 13-Aug-2004 A + PHOTO_OUT SCH, DC HEATER/THERMISTOR 04422 A 111-Aug-2002 B SCH, UV LAMP DRIVER, M450 04421 A 111-Aug-2002 NOTE: THIS SCHEMATIC APPLIES TO THE FOLLOWING PCA'S: CHANGE NOTES NOTES: 1. This schematic is based on the PWB PN, 03974 and applies to PCA PN, 03975 SCH, PCA 04003, PRESS/FLOW, 'E' SERIES 04354D 113-Dec-2007 B S4 CON4 C3 1.0 A 1 2 3 4 04522 D Page Page Page Page Page Page Page Page CONTROL INPUTS