Thomas & Betts 9395 18

Read and understand the following notes while planning and performing the installation:

•Install the interface wiring (for example, building alarm, relay output, battery breaker trip, and X-Slot) separate from the power wiring.The wiring should have double insulation and rated at Uo/U = 300/500 Volts.

•All interface wiring is to be provided by the customer.

•When installing internal interface wiring to X-Slot terminals, route the wiring through the internal opening in the X-Slot communication bay.

•All building alarm inputs or remote features require an isolated normally-open contact or switch (rated at 24 Vdc, 20 mA minimum) connected between the alarm input and common terminal as shown. All control wiring and relay and switch contacts are customer-supplied. Use twisted-pair wires for each alarm input and common.

•The building alarms can be programmed to display the alarm functional name.

•LAN and telephone drops for use with X-Slot cards must be provided by facility planners or the customer.

•The UPS Battery Aux and 48 Vdc ShuntTrip signal wiring from the UPS must be connected to the DC source disconnect device.

•Battery Aux and 48 Vdc ShuntTrip wiring should be a minimum of 1.5 mm2.

•The Remote EPO feature opens all contactors in the UPS cabinet and isolates power from your critical load. Local electrical codes may also require tripping upstream protective devices to the UPS.

•The Remote EPO switch must be a dedicated switch not tied to any other circuits.

•A jumper wire must be connected between pins 1 and 2 onTB1, if the normally-closed Remote EPO contact is not used.

•Remote EPO wiring should be a minimum of 0.75 mm2 and a maximum of 2.5 mm2.

•The maximum distance between the Remote EPO and the UPS cannot exceed 150 meters.

•Alarm relay contacts have a maximum current rating of 5A and a switched voltage rating of 30 Vac and 28 Vdc.

•Alarm relay wiring should be a minimum of 0.75 mm2.

18	UPS 225 - 275 kVA	1027212
	User’s and Installation Guide	Revision B

Contents

Powerware 9395 UPS 225–275kVA User’s and Installation Guide IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Powerware 9395 UPS 225–275kVA User’s and Installation Guide Page 1 Introduction 1.1 UPS standard features Page 1.2 Options and accessories 1.3 Basic system configurations 1.4 Using this manual 1.5 Conventions used in this manual 1.6 Symbols, controls, and indicators 1.7 For more information 1.8 Getting help 2 UPS installation plan and unpacking 2.1 Creating an installation plan 2.2 Preparing the site Model Weight kg Table 2-1.UPS cabinet weights From top of cabinet From front of cabinet Figure 2-1.UPS cabinet dimensions (front view) Figure 2-2.UPS cabinet dimensions (right side view) Page 2.2.2 UPS system power wiring preparation Basic unit rating at 0.9 lagging pF load Units Rating 50/60 Hz Input and output voltage AC input to UPS rectifier (0.98 Min. pF) Terminal function Terminal Function Bus landing Bolt size Load rating Table 2-8.Recommended bypass and output circuit breaker ratings Table 2-9.Recommended DC input circuit breaker ratings 2.2.3 UPS system interface wiring preparation Page 2.3 Inspecting and unpacking the UPS cabinet Figure 2-8.Powerware 9395 UPS (225–275kVA) cabinet as shipped on pallet 3 UPS system installation 3.1 Preliminary installation information 3.2Unloading the UPS cabinet from the pallet and mechan- ical installation •Do not tilt cabinets more than 10° from vertical •Lift the cabinet only with a forklift or damage may occur Figure 3-1.Removing left side shipping bracket 3.3 Battery cabinet installation 3.4 Installing UPS external and battery power wiring Figure 3-3.Conduit and wire entry locations Figure 3-4.UPS power terminal locations Figure 3-5.UPS power terminal detail AA 3.5 Installing interface connections Figure 3-6.Typical alarm relay connection Figure 3-7.Interface terminal locations Terminal TB1 Name Descrition Terminal TB2 Terminal TB3 Figure 3-8.Interface terminal detail AA Figure 3-9.Terminal blocks TB1, TB2, and TB3 connector assignments 3.5.2 TB1 battery interface connections Figure 3-10.Typical battery interface connection 3.5.3 X-Slotconnections 3.6 Installing a remote EPO switch Figure 3-12.Remote EPO switch From remote EPO switch To customer interface Remarks Terminal board TB1 in UPS cabinet Figure 3-13. Normally-Openremote EPO switch wiring Figure 3-14.Normally closed remote EPO switch wiring 3.7 Initial startup 3.8 Completing the installation checklist Installation checklist 4 Understanding UPS operation 4.1 Looking inside the UPS system 4.2 Modes 4.2.2 Bypass mode The critical load is not protected while the UPS is in Bypass mode Figure 4-3.Path of current through the UPS in bypass mode 4.2.3 Battery mode Figure 4-4.Path of current through the UPS in battery mode 4.3 UPS system one line configurations Page Figure 4-6.Typical maintenance bypass panel 5 UPS operating instructions 5.1 UPS controls and indicators 5.2 Using the control panel 5.2.2 Using the LCD and pushbuttons Figure 5-3.Parts of the LCD 5.2.3 Using the menu Menu option Table 5-2.Display function menu map 5.2.4 Mimic screen Figure 5-4.Main menu and Mimic screen (normal mode) Page Page Page Page Table 5-3.Display menu operation 5.2.6 System controls screen Figure 5-5.System Controls screen 5.3 Operation 5.3.2 Starting the UPS in bypass mode 5.3.3 Starting the power module 5.3.4 Transfer from normal to bypass mode Power is present inside the UPS cabinets 5.3.5 Transfer from bypass to normal mode 5.3.6 Transfer from normal to bypass mode and shut down UPS 5.3.7 UPS and critical load shutdown 5.3.8 Charger control 5.3.9 Using the UPS LOAD OFF pushbutton 5.3.10 Using the Remote Emergency Power-offswitch Turn UPS from normal mode to mechanical bypass Turn UPS from mechanical bypass to normal mode 6 Responding to system events 6.1 General 6.2 System event horns 6.3 System event indicators 6.4 System event messages 7 Communication 7.1 X-Slotcards 7.2 Powerware LanSafe Power Management Software 7.3 Terminal mode MM DD YYYY HH:MM:SS.hh KYWD MESSAGE <CR> <LF Figure 7-3.Sample Event History Log 7.4 Building alarm monitoring 7.5 General purpose relay contact 8 UPS maintenance 8.1 Important safety instructions 8.2 Performing preventive maintenance 8.3 Installing batteries 9 Recycling the used UPS or batteries 10 Product specifications 10.1 Model numbers 10.2 Single module specifications 11 Warranty