Manuals / Brands / Computer Equipment / Power Supply / Thomas & Betts / Computer Equipment / Power Supply

Thomas & Betts 9395 5.3 Operation, 5.2.7 Load off screen, Figure 5-7.Load off screen, Figure 5-6.System controls screen, 5.3.1 Starting the UPS in normal mode

1 74

Download 74 pages, 837.1 Kb

Figure 5-6. System controls screen 25.2.7 Load off screen

The load off screen appears when the LOAD OFF pushbutton is selected from the main menu bar or System Controls menu bar.This screen allows the LOAD OFF process to be aborted if the LOAD OFF pushbutton was pressed accidentally. Figure 5-7 shows the Load Off screen. For detailed information about using the LOAD OFF and shutdown screens, see Chapter 5, “UPS operating instructions.”

Figure 5-7. Load off screen

5.3 Operation

5.3.1 Starting the UPS in normal mode

To start the UPS system:

1.If the UPS contains input breaker CB1, verify that input breaker CB1 is open.

2.Close the UPS input feeder circuit breaker.

3.Close the UPS bypass input feeder circuit breaker.

4.Observe the UPS control panel display becoming active, indicating logic power.

5.Press the CONTROLS pushbutton on the main menu bar.The system controls screen appears.

1027212

UPS 225 - 275 kVA

Revision B	User’s and Installation Guide

Contents

Powerware 9395 UPS 225–275kVA User’s and Installation Guide IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Powerware 9395 UPS 225–275kVA User’s and Installation Guide Page 1 Introduction 1.1 UPS standard features Page 1.2 Options and accessories 1.3 Basic system configurations 1.4 Using this manual 1.5 Conventions used in this manual 1.6 Symbols, controls, and indicators 1.7 For more information 1.8 Getting help 2 UPS installation plan and unpacking 2.1 Creating an installation plan 2.2 Preparing the site Model Weight kg Table 2-1.UPS cabinet weights From top of cabinet From front of cabinet Figure 2-1.UPS cabinet dimensions (front view) Figure 2-2.UPS cabinet dimensions (right side view) Page 2.2.2 UPS system power wiring preparation Basic unit rating at 0.9 lagging pF load Units Rating 50/60 Hz Input and output voltage AC input to UPS rectifier (0.98 Min. pF) Terminal function Terminal Function Bus landing Bolt size Load rating Table 2-8.Recommended bypass and output circuit breaker ratings Table 2-9.Recommended DC input circuit breaker ratings 2.2.3 UPS system interface wiring preparation Page 2.3 Inspecting and unpacking the UPS cabinet Figure 2-8.Powerware 9395 UPS (225–275kVA) cabinet as shipped on pallet 3 UPS system installation 3.1 Preliminary installation information 3.2Unloading the UPS cabinet from the pallet and mechan- ical installation •Do not tilt cabinets more than 10° from vertical •Lift the cabinet only with a forklift or damage may occur Figure 3-1.Removing left side shipping bracket 3.3 Battery cabinet installation 3.4 Installing UPS external and battery power wiring Figure 3-3.Conduit and wire entry locations Figure 3-4.UPS power terminal locations Figure 3-5.UPS power terminal detail AA 3.5 Installing interface connections Figure 3-6.Typical alarm relay connection Figure 3-7.Interface terminal locations Terminal TB1 Name Descrition Terminal TB2 Terminal TB3 Figure 3-8.Interface terminal detail AA Figure 3-9.Terminal blocks TB1, TB2, and TB3 connector assignments 3.5.2 TB1 battery interface connections Figure 3-10.Typical battery interface connection 3.5.3 X-Slotconnections 3.6 Installing a remote EPO switch Figure 3-12.Remote EPO switch From remote EPO switch To customer interface Remarks Terminal board TB1 in UPS cabinet Figure 3-13. Normally-Openremote EPO switch wiring Figure 3-14.Normally closed remote EPO switch wiring 3.7 Initial startup 3.8 Completing the installation checklist Installation checklist 4 Understanding UPS operation 4.1 Looking inside the UPS system 4.2 Modes 4.2.2 Bypass mode The critical load is not protected while the UPS is in Bypass mode Figure 4-3.Path of current through the UPS in bypass mode 4.2.3 Battery mode Figure 4-4.Path of current through the UPS in battery mode 4.3 UPS system one line configurations Page Figure 4-6.Typical maintenance bypass panel 5 UPS operating instructions 5.1 UPS controls and indicators 5.2 Using the control panel 5.2.2 Using the LCD and pushbuttons Figure 5-3.Parts of the LCD 5.2.3 Using the menu Menu option Table 5-2.Display function menu map 5.2.4 Mimic screen Figure 5-4.Main menu and Mimic screen (normal mode) Page Page Page Page Table 5-3.Display menu operation 5.2.6 System controls screen Figure 5-5.System Controls screen 5.3 Operation 5.3.2 Starting the UPS in bypass mode 5.3.3 Starting the power module 5.3.4 Transfer from normal to bypass mode Power is present inside the UPS cabinets 5.3.5 Transfer from bypass to normal mode 5.3.6 Transfer from normal to bypass mode and shut down UPS 5.3.7 UPS and critical load shutdown 5.3.8 Charger control 5.3.9 Using the UPS LOAD OFF pushbutton 5.3.10 Using the Remote Emergency Power-offswitch Turn UPS from normal mode to mechanical bypass Turn UPS from mechanical bypass to normal mode 6 Responding to system events 6.1 General 6.2 System event horns 6.3 System event indicators 6.4 System event messages 7 Communication 7.1 X-Slotcards 7.2 Powerware LanSafe Power Management Software 7.3 Terminal mode MM DD YYYY HH:MM:SS.hh KYWD MESSAGE <CR> <LF Figure 7-3.Sample Event History Log 7.4 Building alarm monitoring 7.5 General purpose relay contact 8 UPS maintenance 8.1 Important safety instructions 8.2 Performing preventive maintenance 8.3 Installing batteries 9 Recycling the used UPS or batteries 10 Product specifications 10.1 Model numbers 10.2 Single module specifications 11 Warranty