ASSEMBLY

DECK / MOTOR FEEDLINE

Install the 1” hose with the 90 degree flange on the front side of the motor to the inside upper oil port of the solenoid valve. Secure to motor with flange kit, and install swivel fittings on the other end. Install the other 1” hose with the 60 degree flange on the back side of the motor to the inside lower oil port of the solenoid valve.

Install split hoses around hydraulic hoses where they contact sharp edges, or any other edges that may rub hoses.

Be sure that all grease zerks are installed in the draft beam pin bosses. Grease all areas of the draft beam according to the instructions in the maintenance section. Re-check all fittings for tightness and be sure teflon tape has been used at all connections.

Fill hydraulic tank with fluid as recommended in the maintenance section. BE SURE TO OPEN THE BALL VALVES. Start the tractor and operate the inboard cylinder through the entire stroke and the outboard cylinder through the bottom ¾ stroke repeatedly to clear the lines of air. DO NOT run outboard cylinder out to full stroke until stop bolt has been adjusted!

Check for oil leaks at all fittings and connections using a piece of paper or cardboard. If a leak is found, you must shut down the tractor and set the cutter head on the ground. Before attempting to fix the leak, you must actuate the lift valve handles several times to relieve any pressure in the lines. DO NOT USE HANDS TO

CHECK FOR FLUID LEAKS!

Raise the three point hitch and check the tractor internal hydraulics, fill to proper level if needed.

STOP BOLT ADJUSTMENT

Extend the outboard cylinder all the way out. Adjust the stop adjustment bolt (located on the top of the draft beam) out until it is up against the bonnet. Lock the bolt down with the ¾” hex nut.

NOTE: When the outboard cylinder is fully extended, the bonnet or deck should either be up against the stop or if travel locks are installed, it should be up against the travel lock. It may be necessary to use either external or internal slugs on the cylinder to get the correct stroke. If the cutter head is against the stop and the cylinder has stoke remaining, serious damage will occur.

Proceed to final preparation for operation instructions on the next page.

Assembly Section 2-22

Page 45 Page 47
Page 46
Image 46
Tiger Products Co., Ltd JD 72-7520 manual Assembly Deck / Motor Feedline, Stop Bolt Adjustment
Page 45 Page 47

JD 72-7520 specifications

Tiger Products Co., Ltd is renowned for its innovative machinery solutions, and one of its standout offerings is the JD 72-7520 model. This advanced machine is designed to meet the diverse needs of the woodworking and manufacturing industries, providing a range of features that enhance operational efficiency and precision.

The JD 72-7520 is characterized by its robust construction, ensuring durability and longevity even in demanding work environments. Built with high-quality materials, this machine can withstand the rigors of continuous use, making it a reliable choice for businesses looking to invest in long-term equipment.

One of the main features of the JD 72-7520 is its powerful motor. This engine drives the machine's operations with superior strength, allowing it to perform heavy-duty tasks effortlessly. The motor's efficiency not only contributes to faster processing times but also results in lower energy consumption, making it an eco-friendly choice for manufacturers.

Technologically, the JD 72-7520 incorporates advanced digital controls that enhance user experience and operational precision. These controls facilitate easy adjustments and settings, enabling operators to fine-tune parameters for different types of materials and desired outcomes. With this level of control, manufacturers can achieve consistent results and maintain high-quality production standards.

Another noteworthy characteristic of the JD 72-7520 is its versatility. Designed to handle various woodworking tasks, the machine can be used for cutting, shaping, and finishing a wide range of materials. This adaptability makes it suitable for different applications, from furniture making to cabinetry and beyond, allowing businesses to expand their service offerings without investing in multiple equipment types.

Moreover, the JD 72-7520 places a strong emphasis on safety features. Enhanced user protection mechanisms are integrated, minimizing the risk of accidents during operation. These include safety guards, emergency stops, and sensors that prevent mishaps, making it a safe working environment for operators.

In summary, the Tiger Products Co., Ltd JD 72-7520 is an extraordinary machine that combines power, efficiency, and safety. Its durable construction, advanced digital controls, versatility, and emphasis on user safety make it a valuable asset for any woodworking or manufacturing business looking to enhance productivity and quality. Whether used in small workshops or large manufacturing facilities, the JD 72-7520 stands out as a top choice in its category.
Top Page Image Contents