Topcom DIABLO 100 Buttons see folding page for the picture, Display, Operation

ENGLISH

1Buttons (see folding page for the picture)

1.	Numerical buttons		8.
2.	Off -hook button		9.
3.	Redial / Pause button /P		10.
4.	Flash R/ INT		11.
5.	Direct memory button M1		12.
6.	Paging button	(to retrieve the handset)	13.
7.	Mute button

2Display

On hook button

Charge indicator/ On line (LED) Call log/Scroll Up /

Scroll Down Key lock

Program/Memory button /

You are online			There are more digits on the left
INT = Internal communication
EXT = External communication			There are more digits on the right
New numbers in call list			Program mode
The keypad is locked	- x -		x = handset number
The antenna indicates the quality of reception		/	Answered/Unanswered calls
The antenna blinks when the handset is out of range!
Memory records are being retrieved or set up	hh:mm		Time: hh = hours, mm = minutes

3Installation (See picture on folding page)

4 Battery low indication

When the battery is empty, the handset no longer carries out operations.

Full battery Empty battery

When you are in the middle of a conversation and the battery is almost empty, the handset will emit a warning signal. Place the handset on the base unit to charge.

5Operation

5.1Outgoing calls

5.1.1 Making a phone call or redialing one of the last 5 numbers

Enter the desired telephone number or press the Redial key to dial out one of the last 5 numbers Î press the scroll keys a few times until the desired number appears on the display ÎPress the Off-hook button to dial out ÎPress the on-hook button when you want to terminate the call.

Note: Press the Mute button during a conversation. to deactivate or activate the microphone.

Note: You can set the volume between 1-5 by pressing the scroll button . 5.1.2 Call setup with dial preparation

Enter the desired telephone number. An incorrect number can be corrected by means of the Mute button. ÎPress the Off-hook button

. The number will be dialled automatically. ÎPress the On-hook button when you want to terminate the call.

5.2Incoming calls

When a call comes in, the handset will start to ring. ÎPress the Off-hook button to answer the incoming call. To end the call press

the On-hook button .

5.3Programming memory numbers

You can program 10 indirect numbers (of max. 24 digits) in the phone’s memory.

Press the Memory button short. The first entry will be shown on the display Î Press and hold the Memory button until the - icon appears on the display. ÎEnter the location (0-9) where you want to store the telephone number under. ÎEnter the telephone number you whish to store.ÎPress the Memory button again to confirm. ÎYou will hear a confirmation tone and the next entry will

appear. To leave the memory programming, press the on-hook button.

Note: If you wish to insert a pause, press the Redial/Pause button /P on the location where you want a pause of 3 sec.

5.4Calling a memory number

Press the Memory button ÎScroll with the Up/Down keys to the entry you want to dial (0-9). ÎPress the Off-hook button

. The memory number will be dialled automatically. ÎPress the On-hook button to terminate the call.

5.5Direct access memory (Key 1,2,3 and M1)

The product has 3 locations (Key ‘1’, ‘2’ and ‘3’) where you can store a number under and dial it by pressing and holding one of these keys in standby. The phone will automatically take the line and dial the number which is stored under this key. The number stored under key ‘1’ can also be dialed out by pressing the ‘M1’-key shortly in standby.

5.5.1 Programing the direct memory keys

Press the Memory button short. Press and hold the Memory button until the -icon appears on the display. Press and hold one of the 3 direct memory keys (Key 1,2 or 3) where you want to store the number under until ‘Sx - _’ appears. ÎEnter the telephone number you whish to store. ÎPress the Memory button again to confirm. ÎYou will hear a confirmation tone and the next entry will appear.

To leave the direct memory programming, press the On-hook button .

5.6Paging

Press the Paging button on the base unit, the handset emits a ringing signal to help you find a lost handset. Press any key to stop the ringing on all handsets.

5.7Programming procedure

You can change the ring melodie, volume, day, time etc... by going into the program procedure: To go into the program procedure you have to press and hold the Program button until the icon starts to flash. Î Press the Program button again to change the first setting. Each time you press the Program button you will confirm the previous setting and jump to the next setting:

Topcom Diablo 100/Twin/Triple/Quattro 3