How to replace the lamp unit | Toshiba 62HMX84, 52HMX84 instruction

How to replace the lamp unit

Required tool: Manual Phillips screwdriver; gloves.

Optional tool: 5/32” or 4mm Allen wrench.

1. Turn off the TV and unplug the power cord.

WARNING: Eye damage may result from

directly viewing the light produced by this lamp. Always turn off the TV and unplug the power cord before opening the lamp unit door.

2. STOP! Allow the lamp to cool for at least one (1) hour before replacing it.

CAUTION: HOT SURFACE

The temperature of the lamp immediately

after use exceeds 392ûF (200ûC). Touching the lamp before it has cooled will result in severe burns. ALLOW THE LAMP TO COOL FOR AT LEAST ONE (1) HOUR BEFORE REPLACING IT.

3. On the lamp unit door on the side of the TV, loosen the thumb screw by hand or by using a 5/32” or 4mm Allen wrench, and then remove the lamp unit door.

TV back

Thumb screw

Lamp unit door detail

WARNING: RISK OF

ELECTRIC SHOCK! The lamp

unit door is provided with an interlock to reduce the risk of electric shock and excessive ultraviolet radiation. Never defeat its purpose or attempt to service without removing the lamp unit door completely. Failure to follow this WARNING may result in death or serious injury.

4. Using a manual Phillips screwdriver, loosen the two screws on the lamp unit.

Lamp unit screws

WARNING: RISK OF

ELECTRIC SHOCK!

TO REDUCE THE RISK OF ELECTRIC SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS SPECIFIED HEREIN. REFER ALL SERVICING NOT SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE PERSONNEL. Failure to follow this WARNING may result in death or serious injury.

Introduction


Connecting	yourTV


Usingthe	RemoteControl


Settingup	yourTV


UsingtheTV’s	Features


Appendix


Index

(Continued on next page)

61

Image 61

Toshiba 62HMX84, 52HMX84 owner manual How to replace the lamp unit, Temperature of the lamp immediately

Contents

Index Dlptm Projection Television Dear Customer Lamp Unit Replacement Installation Important Safety Instructions Care Service Important notes about your DLP projection TV Important Safety Information Introduction Introduction Introduction Connecting YourTV ControlWelcome to Toshiba Exploring your new TV Connecting an antenna or cable TV Connecting your TVConnecting your TV Connecting a cable converter box Connecting a VCRUsing You will need Three coaxial cables Connecting a cable converter box and VCR Connecting a DVD player or satellite receiver and a VCR From Antenna Stereo VCR From DTV Antenna Connecting a camcorder Connecting two VCRs One Hdmi cable type a connector Connecting an Hdmi or a DVI device to the Hdmi inputsOne pair of standard analog audio cables Connecting an audio system Preparing the remote control for use Using the remote controlInstalling the remote control batteries Remote Control functional key chart Using the Remote Control CBL/SAT Audio VCR TV/VCR TV/SAT Searching and sampling the code of a device Device code setup Usingthe RemoteControl Setting up your TV Features Connecting YourTVIntroduction Appendix Index Device code table VCR setup codes CD Player setup codes Learning about the remote control Introduction Connecting YourTV Usingthe RemoteControl Setting up your TVSettingup yourTV UsingtheTV’s Features Selecting the antenna input Changing the on-screen display language Adding channels to the TV’s memory Introduction Connecting YourTVProgramming channels automatically To program channels automatically Selecting the Quick Restart Changing channelsAdding and erasing channels manually Enter Adjusting the channel settings Using the TV’s featuresIntroduction Connecting YourTV Usingthe Control Press y or z to highlight Using the TV’s FeaturesFavorite CH Press Enter to display the Favorite CH menu Labeling channels UsingtheTV’s Features AppendixPress z or y to highlight Clear Natural picture size Selecting the picture size Setting your Usingthe RemoteControl Scrolling the TheaterWide picture TheaterWide 2 and 3 only Press Enter to display the Scroll Adjustment modeTo raise the picture, press y To lower the picture, press z Usingthe RemoteControl Settingup YourTV Using the Auto Aspect featurePress y or z to highlight Auto ASPECT, and then press Press y or z to select ON, and then press Enter To close the POP window Press Split again or Exit Using the POP double-window feature Switching the speaker audio main or POP Switching the main and POP picturesUp TV Double-Window aspect ratio Using the programmed channel search function About the auto favorite feature Using the favorite channel search function Using the V-CHIP menu Using the Locks menuEntering the PIN code If you cannot remember your PIN code OFF To release your setting Unlock Enable BlockingTV Rating Independent rating system for broadcasters Press z or y to select an item Mpaa Rating Mpaa Rating Independent rating system for movies Unlocking programs temporarily Locking channelsRepeat steps 2 and 3 for other channels Press y or z to highlight Clear ALL, and then press Enter Changing the PIN code Locking the video inputsOFF From the Locks menu, press y or z to highlight NEW PIN Code Selecting the picture mode Adjusting the pictureAdjusting the picture quality Press x or to select the mode you prefer Selecting the color temperatureSaving your new preferences Resetting picture adjustments Using the CableClear DNR featureReset Done Connecting YourTV Control Selecting the Lamp modeSelecting the cinema mode Cinema Mode Selecting the video input source Press y or z to highlight Caption or TEXT, and then press Using the closed caption featureTo view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the on timer To display the time on-screen Press Recall Muting the sound Adjusting the soundSelecting stereo/SAP broadcasts Using Remote Using the WOW surround sound featureAdjusting the sound quality Settingup YourTV UsingtheTV’s Features Appendix Index Enjoying the Dolby Virtual sound feature Using the StableSound feature Resetting your audio adjustmentsTo turn off the StableSound feature Select OFF in above Selecting the Audio OUT sound Turning off the built-in speakersTo turn on the built-in speakers Select on in above Understanding the last mode memory feature Understanding the auto power off featureSelecting the background of the menu display Displaying on-screen information When to replace the lamp unit Appendix Lamp unit replacement User-replaceable componentU.S Temperature of the lamp immediately How to replace the lamp unit Cleaning the lamp unit glass Replace the thumb screw and hand-tighten Lamp unit disposal LED indications VIDEO/AUDIO Input Specifications Troubleshooting Limited United States Warranty Limited Canada Warranty Audio OUT sound, selecting IndexPage Page Manufactured by