To change your Pass Code | Toshiba DKT2004-CT specs

Features

Call Forward

•Call Forward Busy/Do Not Disturb/No Answer – Forwards all calls to your station whenever you are busy, in the DND mode, or after ringing and you do not answer the call within a designated time (set by you when you enable the feature).

•Call Forward Cancel – Cancels the set Call Forward feature. Notice that each category of Call Forward has a different code for canceling.

Station Call Forward Procedures

The following table contains Call Forward Button sequences. You can do a Call Forward function by entering the button sequence as described.

Some Call Forward features require a Pass Code entry. Use the following procedure to change your Pass Code.

➤To change your Pass Code

➤Press Extension button + + ext. no. + old Pass Code (1~15 digits) + + new Pass Code (1~15 digits) + .

➤To use the Call Forward button sequence

➤Follow the instructions in the following table, shown under “Button Sequence.” Some features require additional input, such as:

•Destination – If the destination is an outside number, press after entering the destination. The CTX accepts destination numbers of up to 32 digits.

•Timer – This is a two digit entry representing how long (eight to 160 seconds) your telephone should ring before forwarding the call. If you enter one digit, you must press after entering the single digit.

•Pass Code – A four-digit code established by system programming to prevent unauthorized changes. The code applies to the station to be forwarded; not to the station entering the code.

Note In the following table, (Tone) means that a confirmation tone will play at that point in the sequence.

Strata DKT2004-CT Cordless Digital Telephone 10/02

31

Image 43

Toshiba DKT2004-CT manual To change your Pass Code, To use the Call Forward button sequence

Contents

DKT2004-CT Cordless Digital Telephone User Guide Publication Information Toshiba America Information SYSTEMS, INC. Tais Toshiba America Information Systems, Inc Contents Features Iii Contents Organization Introduction Calls attention to important instructions or information Conventions Related Documents/Media Viii Grand Tour Benefits Applications Benefits Cordless Digital Telephone Standard Parts Base Unit Controls and Functions Charge LED Batt Charge LED Power on LED Features Review Safety Instructions Installation Ratings are Input 120VAC 14W Output 10VDC 500mA Installation Select Location To use with a desk telephone Connect and Apply Power to Base UnitConnect Telephone Cords To use as a stand-alone telephone Line In to DKT Circuit To remove the belt clip Install Handset Battery PackAttach Belt Clip to Handset optional To attach the belt clip to the handset To charge the handset’s battery pack Removing and Charging Your Battery PackCharging Extra Battery Packs To remove the handset’s battery pack Tips on Extending Battery Pack Life Installing Optional HeadsetOn a Call Standby Mode Installation Entering Program Mode Configuration3 Configuration Mute Handset Volume LevelRinger Volume Level Handset Charging the Handset Using the Handset To transfer an active call Switching a Call to Your Cordless Digital Telephone Vol Switching a Call to the Desk Telephone To dial a stored number Using MemoryTo store a number To erase a stored number Chain Dialing Account Code Calls Features Verified/Non-Verified Account Codes To dial using Forced Account CodesForced Account Codes Voluntary Account Codes Verified/Non-Verified To dial using the Account Code buttonTo enter an Account Code using access codes Automatic Busy Redial Automatic Callback To cancel ACBTo set Automatic Callback Station Auto RedialCall Forward System Call Forward Categories Call Forward Settings To use the Call Forward button sequence To change your Pass Code Call Forward Any Call Set for Another Station Call Forward Incoming Line Calls Call Forward System Call Park Orbits To retrieve a parked call To park a call To perform Call Pickup Call PickupGroup Pickup Page/Internal Call Pickup For Calls On Hold Dialing Description Direct Station Selection Buttons Hotline Call WaitingTo connect directly to another station’s extension Do Not Disturb Setting DND for Another Extension To unlock a door Door LocksTo deactivate DND for another extension To change your DND Pass Code To answer a door phone call Door PhonesDoor Phone Name/Location To call/monitor a door phone Emergency RingdownHeld Calls Placing Line Appearances or DN Calls on Hold 7 5 Using Automatic HoldSwitching Between Calls Retrieving Held Calls Subaddress Isdn Outgoing Calling Responding to a Lit Msg LED Message Waiting To make an OCA call Off-hook Call AnnounceOverride Calls Busy Override To perform Executive Override Do Not Disturb OverrideExecutive Override To use DND Override Privacy Override Class of Service OverrideTo perform Class of Service Override Paging All Call Answering aEmergency To use Privacy Release To set/cancel PrivacyPrivacy Redial Speed Dial Release and Answer To change Tone Dialing Making a Call Using Speed DialTone/Pulse Dialing Voice Mail Direct Transfer Voice Mail Direct Transfer Feature Feature Access Code Sequences Account Code Feature Access CodesCall Forward Any Calls Internal and External Call Forward External Calls Remote Activation Call Forward Remote ActivationCall Park Feature Access Codes Night Ring Answer Feature Feature Access Code Sequences LCD Language ChangePrivate Network Access Code LCR Outgoing Call Message Waiting MW Substitution of Dial Travelling Class Override Feature Feature Access Code Sequences Speed Dial RegisterVolume Control Beep Volume Control Ringing Start Application Feature Access Codes Troubleshooting and Specifications Problem Suggestion Troubleshooting Nine Simultaneous Conversation Channels Range and Performance Base Unit SpecificationsRadio Interference General Index LCD Index