Manuals / Toshiba / Computer Equipment / Printer

Toshiba EM1-33033E Installing The Printer, Centronics Interface 36 pins, Male, RS-232C Interface

Models: EM1-33033 EM1-33033E

1 32

Download 32 pages 8.55 Kb

Page 12

Image 12

5. INSTALLING THE PRINTER

EM1-33033

5. INSTALLING THE PRINTER

WARNING!

Turn the POWER SWITCH to OFF before connecting the power cord or cables.

Serial I/F Cable (RS-232C)

Expansion I/O Cable (Option)

Parallel I/F Cable (Centronics)

Standard: QQ-US	Power Cord	Fig. 5-1
Standard: QQ-US	Power Cord
Option: QQ

NOTE: Only the power cord is provided with this product. If using another cable, it should conform to the following specifications. For more details, please contact your local TOSHIBA TEC service representative.

Centronics Interface (36 pins, Male)

Printer-Side Connector Pin Signals

Expansion I/O Interface (24 pins, Male)

Printer-Side Connector Pin Signals

RS-232C Interface

DB-25S (25 pins, Male,

Metric screw type)

Connector to Printer

PIN No.	Signal
1	Shield
2	RXD

3TXD

4CTS

5RTS

6DTR

7GND

DSR

DB-9P

Connector to PC

PIN No.

Signal

1N.C.

2RXD

3TXD

4DTR

5GND

6DSR

7RTS

8CTS

9N.C.

5-1

Page 12

Image 12

Toshiba EM1-33033E Installing The Printer, Centronics Interface 36 pins, Male, Expansion I/O Interface 24 pins, Male

Contents

Table of Contents B-470-QQ SERIESOwner’s Manual TEC Thermal Printerfor USA only Safety Summary Meanings of Each SymbolSafety Summary Precautions Request Regarding MaintenanceSafety Summary TABLE OF CONTENTS 1. INTRODUCTION 1.2 Accessories1.1 Applicable Model B - 4 7 2 - Q Q2. SPECIFICATIONS 2.1 Printer2.2 Option operation or to rewind labels and backingThis is a paper guide exclusively used for 2.4 Ribbon Media3. OVERVIEW POWER LED GreenERROR LED Red MESSAGE DISPLAY LCD4. DIP SWITCH FUNCTIONS The DIP switches are located to the right of the supply shaft4. DIP SWITCH FUNCTIONS 1 DIP SW5. INSTALLING THE PRINTER Centronics Interface 36 pins, MaleExpansion I/O Interface 24 pins, Male RS-232C Interface6. LOADING THE MEDIA 1. Turn off the power and open the top coverThe printer prints both labels and tags 4. Put the media on the supply shaft Removing the paper holders upper plates from the media guide Setting the feed gap sensor position Media Feed Gap Sensor Adjusting KnobAdjusting Knob An easy way to set the black mark sensor positionBatch type Strip typeBuilt-in rewinder type 7. LOADING THE RIBBON 8. INSERTING THE OPTIONAL FLASH MEMORY CARD 1. Turn the power off3. Turn the power on 9. CARE/HANDLING OF THE MEDIA AND RIBBON 9. CARE/HANDLING OF THE MEDIA AND RIBBON10. GENERAL MAINTENANCE 10.1 Cleaning2. DO NOT APPLY cleaner or detergent directly onto any cover or panel 10.2 Covers and Panels10.3 Removing Jammed Paper 1. DO NOT POUR WATER directly onto the printerCleaning the Cutter Unit 4. Clean the cutter with dry cloth10. GENERAL MAINTENANCE 1. Loosen two screws and remove the cutter coverThreshold setting procedure For firmware version 2.5A or later 10. GENERAL MAINTENANCECommand O N L I N E10.5 Auto Ribbon Saving Mode Threshold setting procedure For firmware version 2.5 or earlier11. TROUBLESHOOTING Error MessageProblem SolutionError Message ProblemSolution denotes a remaining count of unprinted labelsProblem SolutionPage Page PRINTED IN JAPAN EM1-33033