Manuals / Toshiba / Computer Equipment / Printer

Toshiba EM1-33039EE, B-870 SERIES Installation Procedure, Connecting The Power Cord And Cables

Models: B-870 SERIES EM1-33039E EM1-33039EE

1 34

Download 34 pages 52.87 Kb

Page 13

6. INSTALLATION PROCEDURE

6. INSTALLATION PROCEDURE

EM1-33039E

6.1 CONNECTING THE POWER CORD AND CABLES

6. INSTALLATION PROCEDURE

6.1 CONNECTING THE POWER CORD AND CABLES

WARNING!

Turn the POWER SWITCH to OFF before connecting the power cord or cables.

Expansion I/O Cable

Power Cord

Parallel I/F Cable	Fig. 6-1
(Centronics)

Serial I/F Cable (RS-232C)

NOTES: 1. Option B-4800-PC-QM must be installed for use of the high speed PC interface cable.

2.Different cables cannot be used at the same time.

6.2HOLDER STAND INSTALLATION

Fit the left and right side holders into the dowels of the holder base and fasten the side holders to the holder base with the thumbscrews.

Thumbscrew

Left Side Holder

Right Side Holder

Holder Base

Fig. 6-2

Dowel

6-1

Image 13

Toshiba EM1-33039EE owner manual Installation Procedure, Connecting The Power Cord And Cables, Holder Stand Installation

Contents

B-870 SERIES Table of ContentsOwner’s Manual TEC Thermal Printerfor USA only Meanings of Each Symbol Safety SummarySafety Summary Request Regarding Maintenance PrecautionsSafety Summary TABLE OF CONTENTS 1. INTRODUCTION 1.2 ACCESSORIES1.1 APPLICABLE MODEL B - 8 7 2 - Q Q2.1 PRINTER 2. SPECIFICATIONSAuto Ribbon Saving Mode 2.2 OPTION2.4 RIBBON MEDIA2. SPECIFICATIONS 3.1 FRONT/REAR VIEW 3. OVERVIEW3.2 OPERATION PANEL POWER LED GreenTurn the POWER OFF before 4. DIP SWITCH FUNCTIONSswitching 4. DIP SWITCH FUNCTIONS5.2 SETTING UP THE PRINTER 5. SET UP PROCEDURE5.1 REQUIREMENTS FOR OPERATION Interface Cables6.1 CONNECTING THE POWER CORD AND CABLES 6. INSTALLATION PROCEDURE6.2 HOLDER STAND INSTALLATION Head Lever Position 7. LOADING THE RIBBON8. Set the head lock plate 8. LOADING THE MEDIA 8. LOADING THE MEDIA5. Turn the Lock Levers of the Media Holders to the unlock position and readjust the Media position to the center. Then lock the Media Holders securely with the Lock Levers. Fit the Media Guides to the Media. Tighten the screw firmly An easy way to set the black mark sensor position Setting the feed gap sensor position8. The media is now loaded and the sensor position is set. Batch type Backing Paper Holder Media Backing Paper Backing Paper Release Bar1. Turn the power off 9. INSERTING THE OPTIONAL FLASH MEMORY CARD3. Turn the power on Flash Memory Card 10. CARE/HANDLING OF THE MEDIA AND RIBBON 10. CARE/HANDLING OF THE MEDIA AND RIBBON11.1 CLEANING 11. GENERAL MAINTENANCE7. Turn the pinch roller lever to the right 11.3 COVERS AND PANELS 11.2 UNDER THE MEDIA GUIDES11.4 REMOVING JAMMED MEDIA Cleaning the strip unit Cleaning the Cutter UnitThreshold setting procedure 11.5 THRESHOLD SETTING11. GENERAL MAINTENANCE Threshold setting procedure For firmware version 1.3 or earlier Error Message 12. TROUBLESHOOTINGProblem SolutionProblem Error MessageSolution HD001 LF NUL and the print head has aProblem Error MessageSolution ProblemPage E PRINTED IN JAPAN EM1-33039E