Manuals / Toshiba / Computer Equipment / Printer

Toshiba EM1-33039EE, B-870 SERIES owner manual Cleaning the Cutter Unit, Cleaning the strip unit

Models: B-870 SERIES EM1-33039E EM1-33039EE

1 34

Download 34 pages 52.87 Kb

Page 27

■Cleaning the Cutter Unit

11. GENERAL MAINTENANCE

EM1-33039E

11.4 REMOVING JAMMED MEDIA

■Cleaning the Cutter Unit

WARNING!

1.Be sure to turn the power off before cleaning the cutter unit.

2.The cutters are sharp and care should be taken not to injure yourself when cleaning.

1.Loosen two screws and remove the cutter cover.

2.Remove the white screw and media guide.

3.Remove the jammed paper and trash.

4. Clean the cutter with dry cloth. Screw

White Screw	Media Guide

Fixed Cutter

Cutter Cover

Cutter Unit

Swing Cutter

5. Assembling is reverse order of removal.

■Cleaning the strip unit

WARNING!

Fig. 11-7

Be sure to turn the power off before cleaning the strip unit.

1.Lower the backing paper release bar to remove the jammed media.

2.Clean the strip roller and backing paper holder with ethyl alcohol.

Strip Roller

Backing Paper Holder

Backing Paper Release Bar

Fig. 11-8

11-5

Image 27

Toshiba EM1-33039EE, B-870 SERIES owner manual Cleaning the Cutter Unit, Cleaning the strip unit

Contents

TEC Thermal Printer Table of ContentsB-870 SERIES Owner’s Manualfor USA only Safety Summary Meanings of Each SymbolSafety Summary Precautions Request Regarding MaintenanceSafety Summary TABLE OF CONTENTS B - 8 7 2 - Q Q 1.2 ACCESSORIES1. INTRODUCTION 1.1 APPLICABLE MODEL2.1 PRINTER 2. SPECIFICATIONSAuto Ribbon Saving Mode 2.2 OPTIONMEDIA 2.4 RIBBON2. SPECIFICATIONS POWER LED Green 3. OVERVIEW3.1 FRONT/REAR VIEW 3.2 OPERATION PANEL4. DIP SWITCH FUNCTIONS 4. DIP SWITCH FUNCTIONSTurn the POWER OFF before switchingInterface Cables 5. SET UP PROCEDURE5.2 SETTING UP THE PRINTER 5.1 REQUIREMENTS FOR OPERATION6. INSTALLATION PROCEDURE 6.1 CONNECTING THE POWER CORD AND CABLES6.2 HOLDER STAND INSTALLATION Head Lever Position 7. LOADING THE RIBBON8. Set the head lock plate 8. LOADING THE MEDIA 8. LOADING THE MEDIA5. Turn the Lock Levers of the Media Holders to the unlock position and readjust the Media position to the center. Then lock the Media Holders securely with the Lock Levers. Fit the Media Guides to the Media. Tighten the screw firmly An easy way to set the black mark sensor position Setting the feed gap sensor position8. The media is now loaded and the sensor position is set. Batch type Backing Paper Holder Media Backing Paper Backing Paper Release Bar9. INSERTING THE OPTIONAL FLASH MEMORY CARD 1. Turn the power off3. Turn the power on Flash Memory Card 10. CARE/HANDLING OF THE MEDIA AND RIBBON 10. CARE/HANDLING OF THE MEDIA AND RIBBON11.1 CLEANING 11. GENERAL MAINTENANCE7. Turn the pinch roller lever to the right 11.3 COVERS AND PANELS 11.2 UNDER THE MEDIA GUIDES11.4 REMOVING JAMMED MEDIA Cleaning the strip unit Cleaning the Cutter Unit11.5 THRESHOLD SETTING Threshold setting procedure11. GENERAL MAINTENANCE Threshold setting procedure For firmware version 1.3 or earlier Solution 12. TROUBLESHOOTINGError Message ProblemHD001 LF NUL and the print head has a Error MessageProblem SolutionProblem Error MessageProblem SolutionPage E PRINTED IN JAPAN EM1-33039E