Turning OFF the Printer | Toshiba EO1-33088, B-EV4D SERIES guide

2. PRINTER SETUP

ENGLISH VERSION EO1-33088

2.4 Connecting the Cables to the Printer

2.3.2Turning OFF the Printer

CAUTION!

1.Do not turn off the printer power while the media is being printed as this may cause a paper jam or damage to the printer.

2.Do not turn off the printer power while the Green Indicator Lamp is flashing as this may cause damage to the data being downloaded.

1.Before turning off the printer power switch verify that the Indicator Lamp is illuminated in green, not flashing.

2.To turn OFF the printer power press the power switch as shown in the diagram below. Note that ( { ) is the power OFF side of the switch.

Power Switch

E2- 3

Page 14

Image 14

Toshiba B-EV4D SERIES Turning OFF the Printer, ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer

Contents

TOSHIBA Barcode Printer B-EV4D SERIESOwner’s Manual VORSICHT N258CE Compliance for EU only Safety Summary Safety SummaryMeanings of Each Symbol Precautions Request Regarding Maintenance APPENDIX 1 SPECIFICATIONS TABLE OF CONTENTSMAINTENANCE PRODUCT OVERVIEW GLOSSARIES APPENDIX 2 INTERFACEEA2-1 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories1. PRODUCT OVERVIEW Safety consciousness When purchasing the power cord As of August 1.5.3 Rear View 1.5.1 Dimensions 1.5.2 Front View1.5 Appearance Top Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial 1.5.4 InteriorPrint Head Media Holder Media Holder Lock Switch Cover Open Sensor Media Guide Platen 1.5.5 Button and Indicator Lamp Printer status 2. PRINTER SETUP 2.1 Precautions 2.3.1 Turning ON the Printer 2.2 Procedure before Operation2.3 Turning the Printer ON/OFF 2.3.2 Turning OFF the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer 2.4 Connecting the Cables to the Printer c d e f g 2.5 Connecting the Power Adapter and the Power Cord To close the Top Cover 2.6 Opening/Closing the Top CoverTo open the Top Cover 2.7 Loading the Media ENGLISH VERSION EO1-33088 2.7 Loading the Media 2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode How to set the media Strip mode Option How to Load Fanfold Paper Stock Cut mode Option 2. Insert the Media Shaft into the core of the media roll 2.8.1 Media Sensor Calibration 2.8 Media SensorTest, and Dump Mode different type Utilities Print test label sample 2.8.2 Self Print Test and Dump ModeThe following commands should not affect the test print issue D, AX, XS, Z21, Z22 without AY 2.8.2 Self Print Test and Dump Mode Cont E2-16 „ Removing an SD Card 2.9 How to Use an SD Card„ Inserting an SD Card 3.1.1 Print Head 3. MAINTENANCE3.1 Cleaning 4. Do not pour water directly onto the printer 3.1.3 Cover 3.1.4 Media Housing3.1.2 Platen/Sensors 3.2 Care/Handling of the Media Option Symptom 4. TROUBLESHOOTING4.1 Troubleshooting Guide Solutions Status 4.2 Status LampColor 4.3 Removing Jammed Media B-EV4D-GS14-QM-R APPENDIX 1 SPECIFICATIONSA1.1 Printer B-EV4D-TS14-QM-R ENGLISH VERSION EO1-33088 A1.2 Options A1.3.1 Media Type A1.2 OptionsA1.3 Media Option Name Unit mm inch A1.3.1 Media Type ContA1.3.2 Detection Area of the Transmissive Sensor Black Mark A1.3.3 Detection Area of the Reflective SensorA1.3.4 Effective Print Area 5. Line weight should be 3 to 12 dots The figure below shows the effective print area on the media RS-232C Cable description APPENDIX 2 INTERFACEInterface Cables GLOSSARIES Thermal print head A print head using thermal transfer or thermal direct printing methodSupply MediaPage Page EO1-33088

Toshiba EO1-33088, B-EV4D SERIES owner manual Turning OFF the Printer

Models: B-EV4D SERIES EO1-33088

ENGLISH VERSION EO1-33088

2.3.2Turning OFF the Printer