Manuals / Toshiba / Computer Equipment / Barcode Reader

Toshiba EO1-33088, B-EV4D SERIES owner manual Platen/Sensors, Cover, Media Housing

Models: B-EV4D SERIES EO1-33088

1 46

Download 46 pages 23.48 Kb

Page 30

3.1.2 Platen/Sensors

3. MAINTENANCE

ENGLISH VERSION EO1-33088

3.1 Cleaning

3.1.2 Platen/Sensors	1.	Wipe the Platen with a soft cloth moistened with absolute ethyl
	2.	alcohol.
	2.	Remove dust or paper particles from wipe the Black Mark Sensor,
		Feed Gap Sensor, and Cover Open Sensor with a dry soft cloth.

Feed Gap Sensor

Platen

Black Mark Sensor

Cover Open Sensor

3.1.3 Cover

CAUTION!

Do not use any volatile solvents including thinner and benzene, as this may cause discoloration or distortion of the cover.

Wipe the Cover with a dry soft cloth. Wipe off dirt with a soft cloth slightly moistened with mild detergent solution.

3.1.4 Media Housing	Wipe the media housing with a dry soft cloth. Wipe off dirt with a soft
	cloth slightly moistened with mild detergent solution.

E3- 2

Image 30

Toshiba EO1-33088, B-EV4D SERIES owner manual Platen/Sensors, Cover, Media Housing

Contents

B-EV4D SERIES Owner’s ManualTOSHIBA Barcode Printer N258 CE Compliance for EU onlyVORSICHT Safety Summary Meanings of Each SymbolSafety Summary Precautions Request Regarding MaintenanceAPPENDIX 1 SPECIFICATIONS TABLE OF CONTENTSMAINTENANCE PRODUCT OVERVIEWAPPENDIX 2 INTERFACE EA2-1GLOSSARIES 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories1. PRODUCT OVERVIEW Safety consciousnessWhen purchasing the power cord As of August1.5.1 Dimensions 1.5.2 Front View 1.5 Appearance1.5.3 Rear View Top Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial 1.5.4 InteriorPrint Head Media Holder Media Holder Lock Switch Cover Open Sensor Media Guide Platen1.5.5 Button and Indicator Lamp Printer status2. PRINTER SETUP 2.1 Precautions2.2 Procedure before Operation 2.3 Turning the Printer ON/OFF2.3.1 Turning ON the Printer 2.3.2 Turning OFF the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer2.4 Connecting the Cables to the Printer c d e f g2.5 Connecting the Power Adapter and the Power Cord 2.6 Opening/Closing the Top Cover To open the Top CoverTo close the Top Cover 2.7 Loading the Media ENGLISH VERSION EO1-33088 2.7 Loading the Media2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode How to set the media Strip mode OptionHow to Load Fanfold Paper Stock Cut mode Option2. Insert the Media Shaft into the core of the media roll 2.8 Media Sensor Test, and Dump Mode different type Utilities2.8.1 Media Sensor Calibration Print test label sample 2.8.2 Self Print Test and Dump ModeThe following commands should not affect the test print issue D, AX, XS, Z21, Z22 without AY2.8.2 Self Print Test and Dump Mode Cont E2-162.9 How to Use an SD Card „ Inserting an SD Card„ Removing an SD Card 3.1.1 Print Head 3. MAINTENANCE3.1 Cleaning 4. Do not pour water directly onto the printer3.1.4 Media Housing 3.1.2 Platen/Sensors3.1.3 Cover 3.2 Care/Handling of the Media OptionSymptom 4. TROUBLESHOOTING4.1 Troubleshooting Guide Solutions4.2 Status Lamp ColorStatus 4.3 Removing Jammed Media APPENDIX 1 SPECIFICATIONS A1.1 PrinterB-EV4D-GS14-QM-R B-EV4D-TS14-QM-R ENGLISH VERSION EO1-33088 A1.2 OptionsA1.3.1 Media Type A1.2 OptionsA1.3 Media Option NameA1.3.1 Media Type Cont A1.3.2 Detection Area of the Transmissive SensorUnit mm inch A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaBlack Mark 5. Line weight should be 3 to 12 dots The figure below shows the effective print area on the mediaAPPENDIX 2 INTERFACE Interface CablesRS-232C Cable description GLOSSARIES Thermal print head A print head using thermal transfer or thermal direct printing methodSupply MediaPage Page EO1-33088