Manuals / Toshiba / Computer Equipment / Barcode Reader

Toshiba EO1-33088, B-EV4D SERIES owner manual Removing Jammed Media

Models: B-EV4D SERIES EO1-33088

1 46

Download 46 pages 23.48 Kb

Page 34

Image 34

4. TROUBLESHOOTING

ENGLISH VERSION EO1-33088

4.3 Removing Jammed Media

Flashing speed of the LED

Status	Flashing interval
Flashing slowly	1 sec.
Flashing at medium speed	0.5 sec.
Flashing fast	0.2 sec.

4.3 Removing Jammed Media

This section describes in detail how to remove jammed media from the printer.

CAUTION!

Do not use any tool that may damage the print head.

1.Turn the power off.

2.Open the Top Cover and remove the media roll.

3.Remove the jammed media from the printer. DO NOT USE any sharp implements or tools as these could damage the printer.

4.Clean the Print Head and Platen, then remove any further dust or foreign substances.

5.Load the media again, and close the Top Cover.

E4- 3

Page 34

Image 34

Toshiba EO1-33088, B-EV4D SERIES owner manual Removing Jammed Media

Contents

Owner’s Manual B-EV4D SERIESTOSHIBA Barcode Printer CE Compliance for EU only N258VORSICHT Meanings of Each Symbol Safety SummarySafety Summary Precautions Request Regarding MaintenanceAPPENDIX 1 SPECIFICATIONS TABLE OF CONTENTSMAINTENANCE PRODUCT OVERVIEWEA2-1 APPENDIX 2 INTERFACEGLOSSARIES 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories1. PRODUCT OVERVIEW Safety consciousnessAs of August When purchasing the power cord1. PRODUCT OVERVIEW 1.5.3 Rear View 1.5.1 Dimensions 1.5.2 Front View1.5 Appearance 1. PRODUCT OVERVIEWTop Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial 1.5.4 InteriorPrint Head Media Holder Media Holder Lock Switch Cover Open Sensor 1. PRODUCT OVERVIEW1.5.5 Button and Indicator Lamp Printer status2. PRINTER SETUP 2.1 Precautions2.3 Turning the Printer ON/OFF 2.2 Procedure before Operation2.3.1 Turning ON the Printer 2.3.2 Turning OFF the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer2.4 Connecting the Cables to the Printer c d e f g2.5 Connecting the Power Adapter and the Power Cord To open the Top Cover 2.6 Opening/Closing the Top CoverTo close the Top Cover 2.7 Loading the Media ENGLISH VERSION EO1-33088 2.7 Loading the Media2.7 Loading the Media Cont 2.7 Loading the Media Cont Section 2.9.1 Media Sensor CalibrationBatch mode 2.7 Loading the Media ContHow to set the media Strip mode Option2.7 Loading the Media Cont Cut mode Option How to Load Fanfold Paper Stock2.7 Loading the Media Cont 2.7 Loading the Media Cont 2. Insert the Media Shaft into the core of the media roll2.8 Media Sensor Test, and Dump Mode different type Utilities2.8.1 Media Sensor Calibration 2. PRINTER SETUP 2.8.2 Self Print Test and Dump ModeThe following commands should not affect the test print issue Print test label sample2. PRINTER SETUP 2.8.2 Self Print Test and Dump Mode ContE2-16 „ Inserting an SD Card 2.9 How to Use an SD Card„ Removing an SD Card 3.1.1 Print Head 3. MAINTENANCE3.1 Cleaning 4. Do not pour water directly onto the printer3.1.2 Platen/Sensors 3.1.4 Media Housing3.1.3 Cover 3.2 Care/Handling of the Media OptionSymptom 4. TROUBLESHOOTING4.1 Troubleshooting Guide SolutionsSolutions 4.2 Status LampSymptom Solutions4.3 Removing Jammed Media A1.1 Printer APPENDIX 1 SPECIFICATIONSB-EV4D-GS14-QM-R B-EV4D-TS14-QM-R ENGLISH VERSION EO1-33088 A1.2 OptionsA1.3.1 Media Type A1.2 OptionsA1.3 Media Option NameA1.3.2 Detection Area of the Transmissive Sensor A1.3.1 Media Type ContUnit mm inch A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorBlack Mark 5. Line weight should be 3 to 12 dots The figure below shows the effective print area on the mediaInterface Cables APPENDIX 2 INTERFACERS-232C Cable description GLOSSARIES Thermal print head A print head using thermal transfer or thermal direct printing methodSupply MediaPage Page EO1-33088