Loading the Media Cont | Toshiba B-EV4D SERIES, EO1-33088 guide

2.7Loading the Media (Cont.)

2. PRINTER SETUP

ENGLISH VERSION EO1-33088

2.7 Loading the Media

2.7Loading the Media (Cont.)

2.Slide the Media Holder Lock Switch to the Unlock (▲) side to release the Media Holders.

Media Holder Lock Switch

NOTE: Media path

Feed Gap Sensor

Platen

Black mark sensor

NOTES:

1.Refer to the Supply Path Label attached inside of the Top Cover.

2.Make sure that the print side faces up.

3.Cut the leading edge of the media straight with scissors.

NOTE:

Do not forcibly move the Media Guides by hand, as doing so may break the Media Guides.

3.Open the Media Holders.

Media Holder

Media Holder

4.Place a media roll between the Media Holders so that the media is fed with the print side facing up. Fit the projection of the Media Holders into the core. Make sure that the projection of the both Media Holders is engaged with the core firmly.

Media

Media Holder

Media Holder

5.Turn the Media Guide Adjustment Dial in the arrow indicating direction to move the Media Guides outward.

Media Guide

Adjustment Dial

E2- 8

Image 19

Toshiba B-EV4D SERIES, EO1-33088 owner manual Loading the Media Cont

Contents

Owner’s Manual B-EV4D SERIESTOSHIBA Barcode Printer CE Compliance for EU only N258VORSICHT Meanings of Each Symbol Safety SummarySafety Summary Request Regarding Maintenance Precautions PRODUCT OVERVIEW TABLE OF CONTENTSMAINTENANCE APPENDIX 1 SPECIFICATIONS EA2-1 APPENDIX 2 INTERFACEGLOSSARIES Safety consciousness 1.2 Features 1.3 Unpacking 1.4 Accessories1. PRODUCT OVERVIEW 1.1 Introduction As of August When purchasing the power cord 1.5 Appearance 1.5.1 Dimensions 1.5.2 Front View1.5.3 Rear View Media Guide Platen 1.5.4 InteriorPrint Head Media Holder Media Holder Lock Switch Cover Open Sensor Top Cover Feed Gap Sensor Receiver Media Guide Adjustment Dial Printer status 1.5.5 Button and Indicator Lamp 2.1 Precautions 2. PRINTER SETUP 2.3 Turning the Printer ON/OFF 2.2 Procedure before Operation2.3.1 Turning ON the Printer ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer 2.3.2 Turning OFF the Printer c d e f g 2.4 Connecting the Cables to the Printer 2.5 Connecting the Power Adapter and the Power Cord To open the Top Cover 2.6 Opening/Closing the Top CoverTo close the Top Cover ENGLISH VERSION EO1-33088 2.7 Loading the Media 2.7 Loading the Media 2.7 Loading the Media Cont Section 2.9.1 Media Sensor Calibration Batch mode Strip mode Option How to set the media Cut mode Option How to Load Fanfold Paper Stock 2. Insert the Media Shaft into the core of the media roll Test, and Dump Mode different type Utilities 2.8 Media Sensor2.8.1 Media Sensor Calibration D, AX, XS, Z21, Z22 without AY 2.8.2 Self Print Test and Dump ModeThe following commands should not affect the test print issue Print test label sample E2-16 2.8.2 Self Print Test and Dump Mode Cont „ Inserting an SD Card 2.9 How to Use an SD Card„ Removing an SD Card 4. Do not pour water directly onto the printer 3. MAINTENANCE3.1 Cleaning 3.1.1 Print Head 3.1.2 Platen/Sensors 3.1.4 Media Housing3.1.3 Cover Option 3.2 Care/Handling of the Media Solutions 4. TROUBLESHOOTING4.1 Troubleshooting Guide Symptom Color 4.2 Status LampStatus 4.3 Removing Jammed Media A1.1 Printer APPENDIX 1 SPECIFICATIONSB-EV4D-GS14-QM-R ENGLISH VERSION EO1-33088 A1.2 Options B-EV4D-TS14-QM-R Option Name A1.2 OptionsA1.3 Media A1.3.1 Media Type A1.3.2 Detection Area of the Transmissive Sensor A1.3.1 Media Type ContUnit mm inch A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorBlack Mark The figure below shows the effective print area on the media 5. Line weight should be 3 to 12 dots Interface Cables APPENDIX 2 INTERFACERS-232C Cable description GLOSSARIES Media A print head using thermal transfer or thermal direct printing methodSupply Thermal print headPage Page EO1-33088