Connecting the G-LINKcable | Toshiba RD-XS35SC, RD-XS35SU manual

Place the transmitter near the set top box connected to the recorder.

Connections

Connecting the G-LINK®cable

To download program listings the TV Guide On Screen® system needs to be able to change channels on your cable box when the recorder is not in use. Please connect the supplied G-LINK®cable to the G-LINK jack of the recorder. After you connect the G-LINK®cable you will be able to control your cable box using the recorder’s remote control. To connect the G-LINK®cable follow the instructions below.

1 Connect the plug of the supplied G-LINK®cable to the G-LINK jack on the recorder.

2

Cable box

(Keep the power on to receive commands from the recorder.)

1

Introduction

Connections

2 Transmitter Secure the G-LINK®wand underneath the cable box so that the wand’s IR lens faces the front of cable box.

Ensure the G-LINK®wand is at a distance of about one inch from the cable box IR sensor. If you cannot control your cable box, try to adjust the distance or put the G-LINK®wand at another place.

After connecting, make the necessary settings ( page 32).

When you use the recorder for the first time, also make the settings.

Notes

•Do not connect an accessory other than the supplied G-LINK®cable to the G-LINK jack.

•Do not cover the transmitter.

•The TV Guide On Screen® interactive program guide supports cable-ready and cable box as well as over-the-air broadcast. It does not provide listings for satellite services. TV Guide program data and schedules are updated daily through your antenna or cable system once you have completed the TV Guide On Screen® setup.

•Refer to the owner’s manual of the connected set top box as well.

•Power off the recorder overnight or when not in use to allow the TV Guide On Screen® system to receive and update its

listings. If a cable box is connected to this recorder, leave the cable box turned on at all times.

Program listings should start displaying within 24 hours after setting up the TV Guide On Screen® system ( page 32).

Basic setup

25

Image 25

Toshiba RD-XS35SC, RD-XS35SU owner manual Connecting the G-LINKcable

Contents

RD-XS35SU RD-XS35SC This HDD/DVD video recorder employs a Laser System See service procedureMay result in hazardous radiation exposure Location of the required label Important Safety Instructions Additional Safety Instructions When not in use PrecautionsIntroduction Exemptions Power outage Wait Introduction Precautions Connections Accessories Remote control Batteries AAA x Installation procedure Some differences About this productAbout the hard disc drive HDD Playback Restrictions For recording / playback Disc Mark Specification Remarks Using different disc types for different purposesChoosing a disc Disc For playback only Disc Mark Specification Remarks Introduction Choosing a disc On DVD-RAM discsDVD-RAM discs with cartridges are recommended for recording On DVD-RW discs On DVD-R discsMarks on DVD video discs On cleaning discs Structure of disc contentsOn handling discs On storing discs Table of Contents Operating with the remote control Preparation of the remote controlOpen the cover Insert batteries AAA size Close the cover When you connect a TV equipped with audio/ video inputs Connection procedureWhen you connect an audio system Connections Connecting an antenna and TV Connect to a TV equiped with audio/video inputs Connect the power cord of the recorder to a wall outlet You will need to Connecting to cable TV signal This set-up will allow you to When the satellite system has audio/video outputs Connecting to a satellite system Connecting the G-LINKcable Connecting to a TV equipped with component video inputs Make the setting on Connecting to an audio systemPage Basic setup Turning the power on Basic setupStarting up the recorder Startup/finishing closing icons If a message appears Press To select Setup TV Guide On Screen setupPress To select Change system Settings, then press Enter Press To select No, repeat setup Process, then press Enter Country Setup selectionPress / to select, then press Enter Basic setup TV Guide On Screen setup Cable serviceZIP or postal code Cable connection Cable input Tuning channel for the cable box Cable box brand name Press / to select, then press Enter 13Confirmation 12Antenna connection 15Information 14ConfirmationRead the information and press Enter Press Setup Language settingPress / to select Initial settings, then press Enter To select Language, then press Press Setup to display the setup menu Satellite set top box setting Press Adjust or / to set DBS to Not used or Use Press Enter Basic setup Satellite set top box setting RCA Satellite set top box brand code Press / to select Picture/Audio settings, then press Enter Output sound settingPress / to select Audio out select, then press Enter Press / to select the output sound format Once the proper setting is selected, press Press / to select Display settings, then press Enter TV shape settingPress / to select TV shape, then press Press / to select the picture shape When the proper setting is selected, press Operating your TV with the remote control Remote control settingsRelease TV Code Take this step according to your preference and usage JVC Brand code table Press / to select Operational settings, then press Enter Setting up the recorder Press Setup Disabling the remote control for a temporary period Limited One 1 Year Warranty on Parts Limited Ninety 90 Day Warranty on LaborYour Responsibility Rental Units How to Obtain Warranty Services Page Memo Printed on 70% Recycled Paper