Toshiba RD-XS55KU owner manual 149, Items for setting Mail Setting screen

Default Gateway	(Setting unnecessary)	The default gateway that is obtained from the DHCP server is
		displayed.
DNS, DNS Server	Auto	When “Use” is selected, the DNS server address is automatically
		obtained from the DHCP server.
	Manual	Manually enter the DNS server address.
Proxy Server	Up to 63 single-byte	Enter the proxy server address when your provider requires proxy
	alphanumeric characters or	setting.
	symbols
Proxy Port	80	Normally there is no need to change this setting.
		When required, change the value to a number between 1 and 65535.
MAC Address	(Unable to set)	The MAC address that is established for each recorder is displayed.
		It cannot be changed.
Connection Check*		This checks the connection between the recorder and the router.

*When “Connection Check” is pressed, items that were changed on the “Address/Proxy” and “Mail Setting” screens will be saved, and you will not be able to return to the previous setting. Keeping a record of the setting is recommended as a precaution.

Note

•Please contact the router manufacturer when the router DHCP feature is not operating properly (in such a case, an error will occur since the default gateway and the DNS server IP address cannot be obtained).

Introduction RecordingPlayback

Items for setting (Mail Setting screen)

Mail Function	Disable	This will disable the use of the mail function.
	Enable	This will enable the use of the mail function.
Mail Keyword	e.g.: rdstyle	This sets 6-20 single-byte alphanumeric characters so that the email
		for the mail function can be recognized. Symbols should not be
		used since they will cause error and timer recording setting by email
		will not be successful.
POP3 Server Address	e.g.: XXX.XXX.com	This sets the POP3 server address. (Enter up to 63 single-byte
		alphanumeric characters.)
POP3 User Name		This sets the username for accessing the POP3 server. Enter up to
		63 single-byte alphanumeric characters.
POP3 Password		This sets the password for accessing the POP3 server. Enter up to
		16 single-byte alphanumeric characters.
APOP	Enable	This enables the use of APOP (Authenticated POP*).
	Disable	This disables the use of APOP (Authenticated POP*).
Accept	Only	Only one email address is set as the sender.
	All	No specific email address is set as the sender.
From	e.g.:	When “Accept” is set to “Only”, enter the email address of the
	XXXXX@XXX.XXX.com	sender up to 63 single-byte alphanumeric characters.
Completion Notice	Disable	Email notification is not sent when timer recording setting by email is
		completed.
	Secondary Address	When timer recording setting by email is completed, notice is sent to
		the completion-notice contact address.
	Return to sender	When timer recording setting by email is completed, notice is sent to
		the email sender’s address.
	Secondary Address and	When timer recording setting by email function is completed, notice
	sender	is sent to both completion-notice contact address and the email
		sender’s address.
SMTP Server Address	e.g.: XXX.XXX.com	This sets the SMTP server address.**
		Enter up to 63 single-byte alphanumeric characters.
Sender Address	e.g.:	This sets the email address of your internet provider’s email service.
	XXXXXXX@XXX.XXX.com	Enter up to 63 single-byte alphanumeric characters.
Secondary Address	e.g.:	This sets the email address for sending notice when timer recording
	XXXXXXX@XXX.XXX.com	setting by email is completed. Enter up to 63 single-byte
		alphanumeric characters.

•Depending on the recorder’s operating mode, the timer recording setting may not be successful. * APOP: Password encrypting POP. For details, consult your ISP.

** The address of “POP3 Server Address” will be copied if you leave here blank.

Editing

LibraryNetwork Navi Function setup Others

149