Using the menus (Continued)

Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

 

Item

Description

Computer

Y/PB/PR

Video

S-video

Wireless/

 

 

 

 

 

 

 

USB

 

Projector

 

 

 

 

 

 

 

Input

Input source name

Yes

Yes

Yes

Yes

Yes

 

Mode name

RGB input mode [Note 1]

Yes

No

No

No

No

 

Resolution

Resolution (in dots)

Yes

No

No

No

No

 

Frequency

Sync frequency

Yes

No

No

No

No

 

Sync

Sync signal polarity [Note 2]

Yes

No

No

No

No

 

Signal format

Y/PB/PR signal format

No

Yes

No

No

No

 

Video mode

Color method of video signal

No

No

Yes

Yes

No

 

Lamp time

Time of lamp use [Note 3]

Yes

Yes

Yes

Yes

Yes

 

Lamp reset count

The count for lamp replacement

Yes

Yes

Yes

Yes

Yes

 

Total time

The total time that this projector

Yes

Yes

Yes

Yes

Yes

 

 

is used.

 

 

 

 

 

 

 

 

Version

Firmware version [Note 4]

Yes

Yes

Yes

Yes

Yes

Notes

1:The mode of supported RGB signals p.87 is shown.

2:Sync signal polarity shown as P (positive) or N (negative) for [H/V].

3:Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult with a dealer about getting replacement for:

TLPLW9 for TDP-TW95 or TLPLW10 for TDP-TW100 (sold separately).

4:[Version] shows the version of the projector’s internal control program. This version is referred to for customer service, etc.

Note

The displayed information will not be refreshed if the status changes. To refresh the information, dismiss the display, then display it again.

How to use the USB terminal

The supplied wireless LAN USB adapter allows users to connect the projector to a com- puter via wireless communication, which supports IEEE802.11b/g wireless LAN p.46 . (Toshiba does not guarantee the operation of all computers that are IEEE802.11b/g compliant.)

This projector can connect with a commercial USB memory and a USB memory card reader that are USB2.0 compliant, a digital camera or the like and display the JPEG files saved in those devices. p.54

(Toshiba does not guarantee the operation of all USB 2.0-compliant devices.) To connect or disconnect a USB device, use the following procedure:

Connecting USB device

Plug the USB device.

Make sure the orientation is correct then plug the

 

USB device in until it stays securely.

USB device

Disconnecting USB device

qSwitch the input to Wireless/USB and press the MENU button twice to display the Setting display (2), then select and run Unplug device in the Control setting menu.

The processing for disconnecting a USB device starts.

wThe message “Safe to remove the USB device” appears on the screen.

eUnplug the USB device.

Be sure to perform the above operations. Disconnecting a USB device during operation may cause a malfunction or data corruption.

Notes

The projector may not recognize a supported USB device. In such a case, unplug the USB device then re-plug it.

The USB terminal does not support the supplied mouse remote control receiver or a commercial mouse controller.

A USB hub is also not supported.

Precaution

Disconnecting the power plug while the USB device is operating may cause a malfunction or data corruption.

Operations

44

45

Page 23
Image 23
Toshiba TDP-TW95, TDP-TW100 How to use the USB terminal, Displaying Information Status display, Connecting USB device