OFF: if your DSS

® satellite receiver is NON

remote-controllable.

 

 

Satellite channels will be selected by the own

 

channel selector of the DSS

® satellite receiver.

 

The VCR channel should be set to the output

 

channel of the DSS

 

® satellite receiver.

Go to step 8.

 

 

PROGRAM SET UPPRESET

 

 

USE

 

nO C . BOX DSS

 

 

 

 

 

OUTPUT CH

 

 

3 CH

 

 

 

 

 

 

 

 

COnTROL

 

OFF

On

 

 

 

 

 

 

EnD: PROG

 

 

 

7 Select “BRAND TYPE” using

 

 

 

 

STOP, and enter a brand code
of your DSS

 

® satellite receiver using

 

number buttons. Refer
to the table on the next page.

 

 

 

 

 

 

 

 

 

 

Example: For a TOSHIBA DSS

 

 

 

 

® satellite receiver, identified by
number 99.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VCR display

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PROGRAM

 

 

SET UP

 

 

 

PRESET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

nO C . BOX DSS

 

 

 

 

 

 

 

 

USE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUTPUT CH

 

 

 

 

3 CH

 

 

 

 

 

 

 

 

 

OFF

 

On

 

 

 

 

 

 

 

 

COnTROL

 

 

 

 

 

 

 

 

 

 

nO .

 

 

 

 

 

 

 

 

 

 

BRAnD TYPE

99

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EnD: PROG

Make sure that the background of the above display has changed to

the satellite program on channel 200. If not, relocate the DSS® satellite receiver on the VCR so that it can receive the infrared signal.

8

Press

 

PROG. to exit.

 

 

Notes

 

 

7 , the DSS

 

If your satellite channel does not change to 200 in step

® satetllite

 

receiver will not be able to change channels in the timer recording. In this

 

 

case, set “CONTROL” to “OFF” in step

6 .

 

The VCR Plus+ C

3 ® system recording is not available on satellite channels.

 

The DSS

® satellite receiver control is not compatible with the cable box

 

 

control.

 

 

 

 

RECORDING

Buttons to control a remote- controllable DSS® satellite receiverOnce you complete the set-up for a remote

controllable DSS ® satellite receiver, your DSS ® satellite receiver can be controlled by the

following buttons on the remote control of the VCR.POWER (CABLE BOX)
To turn the DSS

® satellite receiver on or off.

CH UP/ CH DOWN (CABLE BOX)

To select satellite channels in the upper or lower direction. (not applicable to some brands of DSS ® satellite receiver.)

Number buttons (0 – 9) To select desired channels to record.

Table of DSS® satellite receiver brand codes

Brand

name of your

Brand code

DSS

® satellite receiver

TOSHIBA99RCA98SONY97

43