Trane XT302C manual Temperature Settings, Installer Setup Procedure

XT302C DELUXE PROGRAMMABLE HEAT-COOL THERMOSTAT

Temperature Settings

Refer to Table 2 for the default program. For 7-Day and

24-Hour Operation, the settings are the same for each day of the week. Refer to the Owners Guide, Pub. No. 22-5127-04, for instructions on changing the default settings.

Table 2. Default Program Settings.

		Heat	Cool	Fan
Period	Time	Setpoint	Setpoint	Setting
Wake	6:00 AM	70°F	78°F	Auto
		(21°C)	(25.5°C)
Leave	8:00 AM	62°F	85°F	Auto
		(16.5°C)	(29.5°C)
Return	5:00 PM	70°F	78°F	Auto
		(21°C)	(25.5°C)
Sleep	10:00 PM	62°F	82°F	Auto
		(16.5°C)	(28°C)

The Leave, Return and Sleep periods may be cleared. For example, the daytime energy-savings period (from Leave to Return) may not be used by the homeowner. To clear any period, follow the instructions in the Owners Guide in the Clearing Schedule Period section.

INSTALLER SETUP

The Installer Setup is used to customize the thermostat for specific systems. Some of the options include Comfort-R™ control activation, Fahrenheit vs. Centigrade temperature display, outdoor temperature display (requires outdoor sensor installation), and system changeover. Installer Setup numbers are listed in Table 3. The table includes all the configuration options and the factory-settings for the XT302C Deluxe Programmable Multistage Thermostat .

NOTE: For most applications, the thermostat factory- settings apply. Review the factory settings in Table 2 and if no changes are necessary, go to the Installer Self-Test section.

IMPORTANT

The chart Customizing Your Thermostat found in the beginning of the Owners Guide (see Fig. 9) must be completed. The homeowner identifies the options you install by referring to this chart.

Installer Setup Procedure

1. Press and hold the Information , Increase ▲,

and Decrease ▼ keys at the same time until all display segments and the first setup number displays

Comfort-R™	OFF
CONTROL
Adaptive	ON
Intelligent
Recovery™
CONTROL
(A HONEYWELL
TRADEMARK)
COOLING	ON
DROOP
TEMPERATURE	FARENHEIT (°F)
DISPLAY
CLOCK	24-HOUR
FORMAT	CLOCK FORMAT
SYSTEM	AUTO/MANUAL
SETTING	(SYSTEM
(HEATING	AUTOMATICALLY
AND	SELECTS
COOLING	HEAT OR COOL;
SETTING)	YOU CAN
	SELECT HEAT,
	COOL OR OFF.)

ON

OFF (CONVENTIONAL RECOVERY)

OFF

CENTIGRADE (°C)

24-HOUR CLOCK FORMAT

MANUAL ONLY (YOU SELECT HEAT, COOL OR OFF.)

AUTO ONLY (SYSTEM AUTOMATICALLY SELECTS HEAT OR COOL)

(all display segments appear for approximately three seconds before the setup number displays). See Figs. 11 and 12.

Set Program Start Time Set Day/Time Temporary Setting Enrg

Hold for	AM			Sav
Em Ht				Room
	PM
Aux Ht
				Outdoor
MonTueWedThuFriSatSun		Heat Cool
WakeLeaveReturnSleep		In Recovery	Auto	Repl Batt
System		DST	Fan
Em Heat OffCool Auto		Wait		OnAuto

M17111

Fig. 10. Display of all the segments of the LCD.

OUTDOOR	NO OUTDOOR	NO OUTDOOR
TEMPERATURE	TEMPERATURE	TEMPERATURE
DISPLAY	IS DISPLAYED	IS DISPLAYED
PROGRAMMING	7-DAY	24-HOUR	CONSTANT
	PROGRAMMING	PROGRAMMING	TEMPERATURE
			SETPOINT
M17110			PROGRAMMING

Figure 9. Customizing Your Thermostat chart, from Owners Guide, Pub. No. 22-5127-04.

Pub. No. 18-HD25D7-5

INSTALLER SETUP	FACTORY SETTING OR OTHER
NUMBER DISPLAY	CHOICE DISPLAY (COLUMN 3
(COLUMN 2 OF TABLE 3)	OR 5 OF TABLE 3)	M10349

Fig. 11. Display of Installer Setup number and option.

69-1213—1 (T8624) 4