XT302C DELUXE PROGRAMMABLE HEAT-COOL THERMOSTAT
Table 3. Installer Setup Options for the XT302C (continued).
| Press Time |
| Press Increase ▲ or Decrease ▼ to change setting |
| |||
| ▲ or ▼ |
|
| ||||
| Installer | Factory Setting |
| Other Choices | Actual | ||
Select | Setup Number | Display |
| Description | Display | Description | Setting |
Minimum On | 33 | 10 |
| 0 thru 15 | Minimum number of minutes |
| |
Time (Cool) |
|
|
| time for compressor |
| (0 thru 15) the compressor |
|
|
|
|
|
|
| will be on during call for |
|
|
|
|
|
|
| cool |
|
|
|
|
|
|
|
|
|
Temperature | 34 | 85 |
| Highest setpoint | 55 to 85 | Temperature range (1°F |
|
range stops in |
|
|
| heating can be set to |
| increments) heating |
|
heating |
|
|
|
|
| setpoint can be set to |
|
|
|
|
|
|
|
|
|
Temperature | 35 | 65 |
| Lowest setpoint | 65 to 99 | Temperature range (1°F |
|
range stops in |
|
|
| cooling can be set to |
| increments) cooling |
|
cooling |
|
|
|
|
| setpoint can be set to |
|
|
|
|
|
|
|
|
|
Temperature | 37 | 0 |
| No difference | 3, 2, 1, |
| |
display |
|
|
| in displayed | higher than actual room |
| |
adjustment |
|
|
| temperature and | temperature |
| |
|
|
|
| actual room |
|
| |
|
|
|
| temperature |
| higher than actual room |
|
|
|
|
|
|
| temperature |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| higher than actual room |
|
|
|
|
|
|
| temperature |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| lower than actual room |
|
|
|
|
|
|
| temperature |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| lower than actual room |
|
|
|
|
|
|
| temperature |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| lower than actual room |
|
|
|
|
|
|
| temperature |
|
|
|
|
|
|
|
|
|
Minimum Off | 38 | 5 |
| 5 minute minimum off | 0 thru 15 | Minimum number of minutes |
|
Time (Heat) |
|
|
| time for the |
| (0 thru 15) the compressor |
|
|
|
|
| compressor |
| will be off between calls for |
|
|
|
|
|
|
| heat |
|
|
|
|
|
|
|
|
|
Minimum Off | 39 | 5 |
| 5 minute minimum off | 0 thru 15 | Minimum number of minutes |
|
Time (Cool) |
|
|
| time for the |
| (0 thru 15) the compressor |
|
|
|
|
| compressor |
| will be off between calls for |
|
|
|
|
|
|
| cool |
|
|
|
|
|
|
|
|
|
Cooling Droop | 41 | 1 |
| Cooling droop | 0 | No cooling droop |
|
|
|
|
| activated |
|
|
|
|
|
|
|
|
|
|
|
Programming | 42 | 0 |
| 1 or 2 |
| ||
| Press Time ▼ to |
|
|
|
|
| |
| bypass |
|
|
|
|
|
|
| and go directly |
|
|
|
|
|
|
| to setup #42 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IMPORTANT
Review the settings to confirm that they match the system. Press Run Program to exit the Installer Setup. The thermostat saves the Installer Setup changes and initiates a reset in order to operate using the new settings.
NOTE: For initial installations only, set the current day and time following the setup reset.
Setting Current Day and Time
1. Press Set Current Day/Time.
Set Current |
|
|
|
|
|
|
| PM |
Program | Day/Time |
| Wake | Leave | Return | Sleep | Mon | |
| Run | Set Current |
|
|
|
|
|
|
Day/Time |
|
| Time |
| Set Program |
|
| |
Hold Temp | Day |
| Settings | Filter | System | Fan |
| |
|
|
|
| Heat/Cool |
|
|
|
|
|
| Daylight | Copy |
|
|
|
|
|
|
| Time |
|
|
|
|
| |
M12951
NOTE: On initial power up or after an extended power loss, 1:00 pm flashes on the display until a key is pressed.
Pub. No.
7 |
