TS16G~64GCF400 | 400X CompactFlash Card | |
|
|
|
|
|
|
Pin
Num
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
| PC Card Memory Mode |
| |||
| Signal Name |
| Pin |
| In, Out |
|
|
| |||
|
| Type |
| Type | |
|
|
|
| ||
|
|
|
|
| |
| HSTROBE10 |
| I |
| I3U |
| HDMARDY11 |
|
|
|
|
|
|
|
|
| |
|
| I |
| I3U | |
|
|
|
| ||
| STOP10,11 |
| |||
|
|
|
|
| |
|
| I |
| I3U | |
| READY |
| O |
| OT1 |
| VCC |
|
|
| Power |
|
|
|
|
| |
|
| I |
| I2Z | |
|
| O |
| OPEN | |
| RESET |
| I |
| I2Z |
|
|
|
|
| |
|
|
|
|
|
|
|
| O |
| OT1 | |
|
|
| |||
|
|
|
|
|
|
| DSTROBE11 |
|
|
|
|
|
|
|
|
|
|
|
| O |
| OT1 | |
|
|
|
| ||
|
| ||||
|
|
|
|
| |
|
| I |
| I3U | |
|
|
|
|
| |
| BVD2 |
| O |
| OT1 |
| BVD1 |
| O |
| OT1 |
| D081 |
| I/O |
| I1Z, |
|
|
|
|
| OZ3 |
| D091 |
| I/O |
| I1Z, |
|
|
|
|
| OZ3 |
| D101 |
| I/O |
| I1Z, |
|
|
|
|
| OZ3 |
| GND |
|
|
| Ground |
|
|
|
|
|
|
Pin
Num
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
PC Card I/O Mode |
|
| True IDE Mode4 | |||
|
|
|
|
|
| |
Signal Name | Pin | In, Out | Pin | Signal Name | Pin | |
Type | Type | Num | Type | |||
|
| |||||
|
|
|
|
|
| |
|
|
|
| |||
HSTROBE10 | I | I3U | 34 | HSTROBE8 | I | |
|
|
|
| |||
I | I3U | 35 | I | |||
|
| |||||
STOP10,11 | STOP8,9 | |||||
|
|
|
| |||
I | I3U | 36 | I | |||
O | OT1 | 37 | INTRQ | O | ||
VCC |
| Power | 38 | VCC |
| |
|
|
|
|
| ||
I | I2Z | 39 | I | |||
O | OPEN | 40 | O | |||
RESET | I | I2Z | 41 | I | ||
|
|
| IORDY7 |
| ||
O | OT1 | 42 | O | |||
|
|
|
|
|
| |
DSTROBE11 |
|
|
| DSTROBE9 |
| |
O | OT1 | 43 | DMARQ | O | ||
| ||||||
|
|
|
|
| ||
I | I3U | 44 | I | |||
DMACK 12 | ||||||
|
|
|
|
| ||
O | OT1 | 45 | I/O | |||
O | OT1 | 46 | I/O | |||
D081 | I/O | I1Z, | 47 | D081 | I/O | |
|
| OZ3 |
|
|
| |
D091 | I/O | I1Z, | 48 | D091 | I/O | |
|
| OZ3 |
|
|
| |
D101 | I/O | I1Z, | 49 | D101 | I/O | |
|
| OZ3 |
|
|
| |
GND |
| Ground | 50 | GND |
| |
|
|
|
|
|
| |
In, Out
Type
I3Z
I3Z
I3U
OZ1
Power
I2U
OPEN
I2Z
ON1
OT113
OZ1
I3U
I1U, ON1 I1U, ON1 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 Ground
Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. Devices should allow for
signals not to consume current.
2)The signal should be grounded by the host.
3)The signal should be tied to VCC by the host.
4)The mode is required for CompactFlash Storage Cards.
5)The
6)If DMA operations are not used, the signal should be held high or tied to VCC by the host. For proper operation in older hosts: while DMA operations are not active, the card shall ignore this signal,including a floating condition
7)Signal usage in True IDE Mode except when Ultra DMA mode protocol is active.
8)Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Write is active.
9)Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Read is active.
10)Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Write is active.
11)Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Read is active.
12)Signal usage in PC Card I/O and Memory Mode when Ultra DMA protocol is active.
Transcend Information Inc. | 7 |
V1.0
