Manuals / Tripp Lite / Computer Equipment / Power Supply

Tripp Lite SU50K3/3PM, SU80K3/3PM Electrical Connection continued, Terminal Wiring Diagrams

Models: SU50K3/3PM SU50K3/3INTPM SU80K3/3INTPM SU80K3/3PM

1 24

Download 24 pages 17.76 Kb

Page 7

Electrical Connection (continued)

Electrical Connection (continued)

Terminal Wiring Diagrams

The following wiring diagrams are organized according to VA. Within each VA grouping, there is a “single loop” connection option (where only one input source is used) and a “double loop” connection option (where two input sources are used).

SU50K3/3PM & SU50K3/3INTPM Models

• Single Loop Connection (one input source used)

• Double Loop Connection (two input sources used)

Note: cables labeled "1B", "2B" and "3B" from the Single Loop Connection diagram

are removed.

SU80K3/3INTPM Model Only

• Single Loop Connection (one input source used)

•Double Loop Connection (two input sources used)

Note: cables labeled "1C", "2C" and "3C" from the Single Loop Connection diagram are removed and connected to the terminal under the "Reserve Breaker".

SU80K3/3PM Model Only

• Single Loop Connection (one input source used)

•Double Loop Connection (two input sources used)

Note: cables labeled "1B", "2B" and "3B" from the Single Loop Connection diagram are removed.

7

Image 7

Tripp Lite SU50K3/3PM, SU80K3/3PM, SU80K3/3INTPM, SU50K3/3INTPM Electrical Connection continued, Terminal Wiring Diagrams

Contents

Intelligent True On-Line UPS Systems 3-Phase 50kVA & AboveOwners Manual SmartOnlineEquipment Connection Warnings Battery WarningsUPS Location Warnings UPS Connection WarningsImportant Safety Warnings continued LED Panel Breakers, Switches & FusesButtons LCD DisplayCommunication Interface Installation ChecklistConnection Checklist Floor Weight Loading TableConnection Checklist Recommended Cable Sizes Terminal Wiring Diagrams Parallel Wiring DiagramsElectrical Connection continued Terminal Wiring DiagramsManual Maintenance Bypass Procedure Parallel Wiring DiagramsShutdown Procedure Start-Up ProcedureSingle UPS Operation continued Start-Up ProcedureManual Maintenance Bypass Procedure Shutdown ProcedureThis procedure removes power from and shuts down the UPS Normal Mode Start-Up Procedure Shutdown ProcedureManual Maintenance Bypass Procedure Operational Modes Operational ModesMultiple UPS Operation Parallel continued Multiple UPS Operation Parallel continued Multiple UPS Operation Parallel continued Start-Up ProcedureManual Maintenance Bypass Procedure Shutdown ProcedureStep 1. For each UPS power module in the parallel configuration which will be placed on bypass, simultaneously press the “OFF” and “” Buttons and hold for 3 seconds. The power modules inverter will turn off its LCD Screen will display “Output Close” and support of the equipment load will be transferred and shared equally among the other UPS power modules in the parallel configuration that have not yet been placed on bypass. As each consecutive power modules inverter is turned off, however, a point will be reached where the power modules which have not yet been placed on bypass will not be able to share the combined load. At this point, the remaining power modules will automatically shut down their inverters, transfer the load to reserve power and display “Bypass Mode” on their LCD Screens Main Menu Measure Page Parameter Setting System Control Event LogOther Information “Measure Page” Sub-Menu E F G H “Parameter Setting” Sub-MenuLCD Display Navigation continued A B C DA B C D LCD Display Navigation continued“System Control” Sub-Menu “Event Log” Sub-MenuUPS Status Code “Other Information” Sub-MenuDry-Contacts Remote Emergency Power Off EPO RS-232 Port/Ethernet Port/SNMP Card Slot Ethernet PowerCommunications continued GENERATOR CONTACTUPS Parallel Communication Port RS-485 PortTERMINAL RESISTOR FOR RS-485 RS-485 PortWarranty Registration LIMITED WARRANTY200503068 1111 W. 35th Street Chicago, IL 60609 USA