ROW Marker Attachment, Bumper Attachment | Troy-Bilt 12212, 12211

PARTS LIST

Models 12211 and 12212

ROW MARKER ATTACHMENT

ROW MARKER ATTACHMENT – PART # 12589 (Complete – Attaches to Furrower Attachment)

MAIN SUPPORT/YOKE ASSEMBLY

PART # 1904522001

BUMPER ATTACHMENT

46	BUMPER ATTACHMENT – PART #12593 (Viewed from front of tiller.)

Image 46

Troy-Bilt 12212, 12211 owner manual ROW Marker Attachment, Bumper Attachment, 1904522001

Contents

7HP Pony REAR-TINE Tiller Recoil Start Model shown See Back Cover for Customer Service information Safety Exercise caution to avoid slipping or falling Keep children and pets away Use slower engine speeds Operating Symbols To Avoid Serious Injury Inspect unit IntroductionAttach Handlebars Attach Reverse Clutch Control Screw the height adjustment handleAttach Forward Clutch Rod Hairpin Cotter Select the proper hole in the clutch Reinstall and hand-tighten the oil fill plug NCheck Gear Oil Level in Transmission If the gap is incorrect Add Motor Oil to Engine Attach Engine Throttle LeverCheck Air Pressure in Tires Attach Wheel Gear Lever Battery Activation and Charging Check Hardware for Tightness Attach Battery Cables and Vent Tube Install Battery Connect Wiring Harness Keyswitch To Operate the Forward Clutch Wheel Gear LeverForward Clutch Engage Reverse Clutch Handlebar Height AdjustmentTo Adjust the Handlebar Height Depth Regulator Engine Throttle Lever Electric Start Keyswitch electric start modelStop on recoil start model only Stop Stops the engine BREAK-IN Operation Pre-Start ChecklistIntroduction Starting and Stopping Engine Stopping the Engine Operating the TillerStarting the Engine Stop Stop position For forward motion of the wheels and tines Keyswitch to OFF to stop the engineTurning the Tiller Around For reverse motion of the wheels and tines Avoid tilling soggy, wet soil Let the tiller do the workTilling depths Avoid making footprints Tilling on slopes Tilling across slopes without using terracesClearing the tines Tilling up and down slopes Power Composting Loading and Unloading Tiller Tiller Lubrication Required Maintenance ScheduleProcedure Every Check Tire Pressure Transmission Gear OIL ServiceCheck Hardware Check for OIL Leaks AIR Cleaner Service Engine CleaningEngine OIL Service CARBURETOR/GOVERNOR Control Adjustments OFF Season Storage Wheel Gear Cable AdjustmentBolo Tines Checking and Adjusting Tension on the Drive Belts Reinstall the belt cover and secure it with the two nutsCutting Edge Tine Threads Forward Drive Belt Removal and Installation Installing the Forward Drive BeltRemoving the Forward Drive Belt Reverse Drive Belt Removal and Installation Removing the Reverse Drive Belt Reconnect the reverse cable wire to the Z-fitting Q, Figure Battery MaintenanceInstalling the Reverse Drive Belt Battery Care in Service Tiller Length Tiller WeightTransmission Gear OIL Specifications Tiller Width Troubleshooting Problem Possible Cause Correction Part Description Models 12211HOOD, Bracket and Depth Regulator QTY Handlebar Assembly and Control Levers Bellcrank See Pg Parts List ENGINE, Support BRACKETS, PULLEYS, BELTS, Belt Cover Part Description QTY Forward Idler Assembly 9621 Drive SHAFT, Input Pinion Shaft and Gear Assemblies Input Pinion Shaft & Gear AssemblyMain Drive Shaft Wheel SHAFT, Eccentric Shaft and Tiller Shaft Assemblies Bolo TINES, Wheels Two ea. Refs 1733398 Hex Locknut, 3/8-16 1982612 HILLER/FURROWER Attachment Electric Start Assembly 96512 Battery, 12 Volt, 9 Amp Incl 9462 Bumper Attachment ROW Marker Attachment1904522001 Description QTY Models 12211ROW Marker Attachment & Bumper Attachment Row Marker Attachment Engine Service and Repair Warranty ServiceReplacement Parts Owner Registration Card