WARNING: To prevent electric shock use only with an extension cord suitable for outdoor use.
15.CORD SETS: Please see your dealer for the appropriated extension cord to use with this product. Make sure your cord set is in good condition, with a cord that is heavy enough to carry the current that your unit will draw. An undersized cord set will cause a drop in line voltage resulting in a loss of power, as well as overheating. The table shown above illustrates the correct size to use depending on the cord length and nameplate amperage rating. If in doubt, use the next heavier size line gauge. The smaller the gauge number, the heavier the cord. To prevent the cord from disconnecting from the unit, use the cord hook shown in the Operating Instructions.
MINIMUM WIRE SIZE FOR EXTENSION CORDS
FOR 120 VOLT APPLIANCES USING 10 - 12 AMPS
Cord Length (ft.) | 25 | 50 | 100 | 150 |
Wire Size (AWG) | 16 | 16 | 14 | 12 |
|
|
|
|
|
16.A data plate on your unit indicates the voltage used. Never connect the unit to an AC voltage that differs from this voltage.
17.Inspect all extension cords and the unit power connection periodically. Look closely for deterioration, cuts or cracks in the insulation. Also inspect the connections for damage. Repair or replace the cords if any defects appear.
18.To prevent disconnection of snow thrower cord from the extension cord during operation,
a.Make a knot as shown, or
b.Use the cord retainer described in this manual
18.When cleaning, inspecting or repairing the unit, make certain the auger and all moving parts have stopped. Disconnect the extension cord to prevent accidental starting.
19.Do not abuse the extension cord. Never carry the snow thrower by the cord or yank on the cord to disconnect it from the receptacle.
20.Keep the extension cord away from heat, oil, and sharp edges to prevent damage.
21.If the extension cord is damaged in any manner while it is plugged in, pull the extension cord from the wall receptacle.
22.Prevent any possible disconnection of the cord receptacle from the extension cord during operation by using the cord retainer and guide bar. Refer to the
23.Avoid accidental starting. Don’t carry a
24.Always unplug the unit and allow it to cool before putting it into storage. Store indoors.
25.Always unplug the unit when not in use, and before performing any maintenance or repairs.
While Operating
1.Walk, never run.
2.Be sure the snow thrower is not in contact with anything before starting the unit.
3.Stay away from the discharge opening at all times. Keep face, hands, and feet away from concealed moving or rotating parts.
4.Be attentive when using the snow thrower, and stay alert for holes in the terrain and other hidden hazards or traffic.
5.Do not use on a gravel surface or crushed rock surfaces. Use extreme caution when crossing gravel/crushed rock drives, walks, or roads.
6.Clear snow from slopes by going up and down. Never go across the slope. Use caution when changing directions. Never clear snow from steep slopes.
7.Never attempt to use the snow thrower on a roof or any steep, inclined, slippery surfaces.
8.Never operate snow thrower without proper guards, plates or other safety protective devices in place, and in working order.
9.Never operate the snow thrower near glass enclosures, automobiles, trucks, window wells, dropoffs, etc. without proper adjustment of the snow discharge angle. Keep children and pets away.
10.Don’t force or overload the snow thrower. The snow thrower will perform at its best and safest when it is run at the rate for which it was designed.
11.Never operate the machine at high speeds on slippery surfaces. Look behind and use care when backing up.
12.Never direct discharge towards people or allow anyone in front of the unit while operating.
13.Wear safety glasses or goggles that are marked as meeting
ANSI Z87.1 standards when operating this unit.
14.Use the unit only in daylight or good artificial light.
15.Avoid accidental starting. Remain in the starting position whenever starting the unit. The operator and unit must be in a stable position while starting. See Starting/Stopping Instructions.
4
Section 2 — Important Safe Operation Practices
