7.Keep hoses clear and unblocked.

8.Bleed air out of hoses before operating.

9.Flush and clean hydraulic system before restarting after servicing.

10.Use “pipe dope” on all hydraulic fittings.

11.Allow time for warm-up before splitting wood.

12.Prime the pump before initial start-up by turning over the engine with spark plug disconnected (if not already done at factory).

13.Split wood along the grain (lengthwise) only.

Never:

1.Use when fluid is below 20° F or above 150° F.

2.Use a solid engine /pump coupling.

3.Operate through relief valve for long.

4.Attempt to adjust unloading or relief valve settings without pressure gauges.

5.Operate with air in hydraulic system.

6.Use teflon tape on hydraulic fittings.

7.Attempt to cut wood across the grain.

8.Attempt to remove partially split wood from the wedge with your hands. Fully retract wedge to dislodge wood with log dislodger.

Raising and Lowering Beam

1.Use control handle to run wedge up and down beam 6 to 8 times to circulate the hydraulic fluid, which will warm and thin the fluid.

2.Place log splitter on a firm, level surface.

To raise the beam for vertical operation:

3.Pull out the horizontal beam lock on the tongue.

4.Pivot beam lock down to release the beam.

5.Move the beam to the vertical position. Secure it with the beam lock on the reservoir tank assembly.

WARNING: Always use the log splitter in the vertical position when splitting heavy logs.

To lower the beam:

1.Pull out the vertical beam lock on the reservoir tank.

2.Pivot beam lock down to release the beam.

3.Carefully pull back on beam and lower it to the horizontal position.The horizontal beam lock will lock automatically. See Figure 4-1.

Figure 4-4

Transporting the Log Splitter

IMPORTANT: Always turn fuel valve to OFF position before transporting the log splitter.

1.Lower the beam to its horizontal position. Make cer- tain the beam is locked securely with the horizontal beam lock.

2.Remove spring clip and clevis pin from jack stand.

3.Support the tongue and pivot the jack stand up against the tongue. See Figure 4-4.

4.Secure with the spring clip and clevis pin previously removed. See Figure 4-4.

5.Attach coupler hitch to a class I or higher 2” ball on a towing vehicle; latch securely.

a.If coupler hitch does not fit on ball: Turn adjustment nut one turn counter-clockwise.

b.If coupler hitch is too loose on ball: Turn adjustment nut one turn clockwise.

6.Connect the safety chains to the towing vehicle.

7.Plug in the tail lights, if so equipped, to the tail light connector on the tow vehicle.

WARNING: Do not tow faster than 45mph and check local, state, and federal requirements before towing on any public road.

NOTE: Use caution when backing up. It is recom- mended to use a spotter outside the vehicle.

4

Operating

Your Log

Splitter

WARNING

Always use the log splitter in the vertical position when splitting heavy logs.

Do not tow faster than 45mph and check local, state, and federal requirements before towing on any public road.

11

Page 10 Page 12
Page 11
Image 11
Troy-Bilt LS 27 TB warranty Raising and Lowering Beam, Transporting the Log Splitter, Never, To lower the beam
Page 10 Page 12

LS 27 TB specifications

The Troy-Bilt LS 27 TB is an innovative garden tiller designed to enhance productivity in any small to medium-sized gardening or landscaping project. This robust machine features a powerful engine and advanced technologies that streamline the tilling process, making it a valuable tool for both amateur gardeners and seasoned horticulture professionals.

One of the standout features of the LS 27 TB is its 27-inch tilling width. This ample width allows users to cover more ground in less time, reducing the number of passes required to prepare the soil. The tiller's adjustable tilling depth—ranging from 1 to 8 inches—enables precise soil preparation for varying plant root depths, ensuring optimal growing conditions for various crops.

Powered by a reliable, easy-start engine, the Troy-Bilt LS 27 TB offers ample horsepower to tackle tough soil conditions without compromising performance. The machine's forward and reverse gear options provide enhanced maneuverability, allowing gardeners to navigate tight corners and difficult spots with ease.

Incorporated into the design is the patented “Cultivator Attachment” system, which allows users to switch from tilling to cultivating tasks effortlessly. This versatility makes the LS 27 TB an excellent choice for multi-purpose gardening, as it can handle not only tilling but also other gardening tasks efficiently.

Safety is a priority with the LS 27 TB, which features a handlebar-mounted control system. This ergonomic design provides users with greater comfort while working, reducing fatigue during extended use. The tiller is also equipped with an automatic engagement system for the tines, ensuring that users can operate the machine with confidence.

Another notable characteristic of this tiller is its durable construction. Built to withstand the rigors of frequent use, the Troy-Bilt LS 27 TB features high-quality materials that ensure longevity. The robust wheels provide excellent traction, making it easier to navigate uneven terrain.

In summary, the Troy-Bilt LS 27 TB is a powerful and versatile tiller that combines innovative features, user-friendly controls, and durability. Whether preparing a small garden bed or working on a larger landscaping project, this tiller offers the performance and versatility needed to achieve gardening goals with ease. Its blend of technology and user-centric design sets it apart in the market, making it an ideal choice for anyone looking to enhance their gardening experience.
Top Page Image Contents