Tunturi S30 owner manual Assembly

training partner. Whatever your goal in training, we are certain this is the training equipment

to get you there. You’ll find information about using your exercise equipment and what makes for efficient training at Tunturi’s website at

WWW.TUNTURI.COM.

ASSEMBLY

Unpack the device and check that all the following parts are in the package (fig. 1):

A. Main mast assembly

B. Leg tubes (2)

C. Tie rods (2)

D. Feet (2)

E. Handlebar

F. Meter mount

G. Meter

H. Shocks (2)

Assembly kit (contents marked with in the spare part list): keep the assembly tools, as you

may need them e.g. for adjusting the equipment.

If you notice that a part is missing, contact the dealer and give the model (S30), serial number and spare part number from the list at the back of the manual. The assembly figures mentioned in the text are at the back of the manual. The package includes a silicate bag for absorbing moisture during storage and transportation. Assemble the device as follows (left, right, front and back are as seen from the exercising position):

ATTACH THE LEGS

Position the main mast assembly so that the S30 label is facing up. Screw the left leg tube

into the main mast as shown, being careful to keep the leg tube in line (fig. 2). NOTE! Do not force. If resistance is felt initially, unscrew and start again. Hand tighten the leg firmly. Attach the right leg in the same manner.

ATTACH THE TIE RODS

Place the hooked end of a tie rod into the left hole on the bottom of the main mast (fig. 3). Gently slide the tie rod bracket into the end of the left tube while simultaneously inserting the threaded end of the tie rod into the tie rod bracket. Slide the bracket with the rod into the tube as far as possible, making sure the bracket is at right angle to the tie rod. Secure the tie

O W N E R ’ S M A N U A L • S 3 0

rod with a 5 mm flat washer and a locking nut. Tighten the nut with the enclosed flat wrench (fig. 4). Repeat for the right tie rod.

ATTACH THE FEET

The feet are labeled “L”and “R” (for left and right). Slide each foot onto its respective leg, making sure the tie rod connects at the bottom of the slot (fig. 4). At this time, tilt the unit back onto the feet.

INSTALL THE SHOCKS

Attach the end of the shock absorber that contains the resistance adjustment mechanism to the left side of the main mast. Insert a shock spacer into the eye of the top end of the shock. With the arrow facing to the rear, secure the shock to the outside of the top, left mounting bracket with a socket head cap screw, two 8 mm flat washers, and a locking nut. Use the flat wrench and the 5 mm hex wrench to tighten. Lift the left foot pedal up and secure the bottom of the shock repeating the same steps as for the upper shock attachment (fig. 5). Install the right shock in the same manner.

ATTACH THE HANDLEBAR

Align the holes on the base of the handlebar to those on the top of the mast, making sure the handlebar end caps are pointing forward. Secure the handlebar with four Allen screws and 6 mm split lock washers (fig. 6). Tighten screws with the 5 mm hex wrench.

ATTACH THE METER

Open the battery case cover on the back of the meter case and insert two 1.5 V AA-batteries to the battery case following the + and - markings. Feed the meter wire, coming out through the top of the vertical frame, through the meter mount and snap the meter mount over the handlebars, making sure the tongue on the handlebar mount aligns with the corresponding groove on the meter mount (fig. 7). NOTE! Be careful not to get the wire caught! Plug the meter cable into the socket on the rear of the meter. Secure the meter into place by setting it on the meter mount and sliding it down until firmly in place. NOTE! Make sure the meter cable is not pinched during the assembly as this can cause the meter to not function correctly (fig. 8).

GB

3