TVS electronic RP-3180 ESC H n, ESC J n, ESC V n1 n2 d1...dk, ESC W xL xH yL yH dxL dxH dyL dyH

ESC H n

[Name]	Select character Double-height mode
[Format]	ASCII	ESC	H	n
	Hex	1B	48	n
[Range]	Decimal	27	72	n
	1 n	8
[Description]	Select character Double-height mode.
ESC I
[Name]	Select character Double-height mode
[Format]	ASCII	ESC	I
	Hex	1B	49
[Description]	Decimal	27	73
	Select character Double-height mode.
ESC J n
[Name]	Print and feed paper
[Format]	ASCII ESC J n
	Hex 1B 4A n
	Decimal 27 74 n
[Range]	0 = n = 255
[Description]	Prints the data in the print buffer and feed the paper [n x vertical or
	horizontal motionunit].
[Details]	After printing is completed, this command sets the print starting
	position to the beginning of the line.
	The paper feed amount set by this command does not affect the
	values set by ESC 2 or ESC 3.
	In standard mode, the printer uses the vertical motion unit (y).
	The maximum line spacing is 1016mm {40"}. When the setting
	value exceeds the maximum, it is converted to the maximum
	automatically.
ESC L
[Name]	Select page mode
[Format]	ASCII	ESC	L
	Hex	1B	4C
[Description]	Decimal	27	76
	Switches from standard mode to page mode.
[Details]	This command is enabled only when processed at the beginning of
	a line in standard mode.
	This command has no effect in page mode.
	The following command is not available in page mode, Print raster
	bit image: GS v 0
	The printer returns to standard mode when power is turned on, the
	printer is reset, or ESC @ is used.
	RP-3180 USER'S MANUAL		17

ESC V n1 n2 d1...dk

[Name]	Printing bit image
[Format]	ASCII	ESC	V	n1	n2	d1...dk
	Hex	1B	56	n1	n2	d1...dk
	Decimal	27	86	n1	n2	d1...dk
[Range]	0 n1,n2	65535
[Description]	n1, n2: number of dot lines in the vertical direction.
	n1 represents the least significant byte and n2 represents the most
	significant byte.
	Number of dot lines=n2 x 256+n1					Ignored when n1=n2=0.
[Details]	Enter the image data following n1 and n2. The amount of image
	data is as follows:Amount of image data=(n2 x 256+n1) x 72 bytes
	The data following n1 and n2 is printed out entirely as image data.
	Enter the data from the leftmost of the top dot line to the bottom
	dot line.
	If you specify bit image without entering CR or LF after inputting
	characters for a rangenot exceeding one line, the characters of
	that line and the bit image are overlapped when printed out. At this
	time, all modifications to characters are valid. Note that the
	characters are not normally printed out when overlapped unless a
	value more than the character height is specified by n2 x n1. You
	can not overlap bit images with stamps or ruler lines. If you specify
	bit images, the stamp or the ruler line is suspended. After the bit
	image is complete, the print-out of stamps or ruler line restarts.
ESC W xL xH yL yH dxL dxH dyL dyH
[Name]	Defining the print area in page mode
[Format]	ASC II	ESC	W	xL	xH yL yH dxL dxH dyL dyH
	Hex	1B	57	xL	xH yL yH dxL dxH dyL dyH
	Decimal	27	87	xL	xH yL yH dxL dxH dyL dyH
[Range]	0 = xL, xH, yL, yH, dxL, dxH, dyL, dyH = 255
	except for dxL = dxH = 0 or dyL = dyH = 0
[Description]	Defines the location and size of the print area.
	Horizontal start point = [(xL + xH x 256) x basic calculation pitch]
	inches
	Vertical start point = [(yL + yH x 256) x basic calculation pitch]
	inches
	Horizontal length = [(dxL + dxH x 256) x basic calculation pitch]
	inches
	Vertical length = [(dyL + dyH x 56) x basic calculation pitch]
	inches
[Details]	When standard mode is selected, this command only executes the
	internal flagging of the printer without affecting the printing in
	standard mode.
	If the horizontal start point or vertical start point is out of the
	printable area, this command is canceled and the next data is
	handled as normal data.
	RP-3180 USER'S MANUAL		18