Vanguard Heating VMH26PRA To Turn OFF GAS To Appliance, Manual Lighting Procedure

Models: VMH26PRA

1 30
Download 30 pages 45.19 Kb
Page 19
Image 19

OWNER’S MANUAL

OPERATING

FIREPLACE

Continued

Pilot Burner

Ignitor

Electrode

Figure 37 - Pilot

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1.Turn control knob clockwise to the OFF position.

2a. Set selector switch in the OFF position.

2b. If Using Optional Hand-Held Re- mote: Set selector switch in the OFF position to keep from draining battery.

Shutting Off Burner Only (pilot stays lit)

You may shut off the burner and keep the pilot lit by doing one of the following:

Turn control knob clockwise to the PILOT position.

Use remote control manual OFF button.

Set selector switch in the OFF position.

MANUAL LIGHTING

PROCEDURE

1.

Follow steps 1 through 6 under Light-

 

ing Instructions, page 18.

2.

Depress control knob and light pilot

 

with match.

3.

Keep control knob pressed in for 30

OPTIONAL REMOTE

OPERATION

Note: All remote control accessories must be purchased separately (see Accessories, pages 28 and 29). Follow installation in- structions on page 16 of this manual.

Thermostat Control Operation

(Optional GHRCTA Series Only) The thermostat control setting on the remote control unit can be set to any comfort level between WARMER and COOLER. The burner will turn on and off automatically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the cen- tral heating system, etc.

For wall thermostat operation, follow in- struction supplied with thermostat acces- sory GWMT1. For wall switch operation follow instructions supplied with GWMS2.

NOTICE: You must light the pilot before using the hand-held re- mote control unit. See Lighting Instructions on page 18.

1.After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjust- ment knob anywhere between HI and LO. Slide the selector switch to the REMOTE position. Note: The burner may light if hand-held remote ON button was on when selector switch was last turned off. You can now turn the burner on and off with the hand-held remote control unit.

IMPORTANT: Do not leave the se- lector switch in the REMOTE posi- tion when the pilot is not lit. This will drain the battery.

IMPORTANT: Be sure to press the ON/OFF buttons on the hand held remote control unit for up to 3 sec- onds to assure proper operation.

GHRC Series Operation:

2a. Press the ON/OFF button to turn the burner on and off. When turning burner off, the pilot will remain lit.

GHRCTA Series Operation:

2b. Press the AUTO/ON/OFF button on the hand-held remote control (see Figure 39, page 20). The lights to the left of the button will show AUTO, ON, or OFF.

In the ON mode, the burners will ignite. The heater is in manual mode when ON is lit.

In the AUTO mode, the thermostat in the hand-held remote unit con- trols the room temperature. To in- crease the room temperature, press the top arrow of the TEMP button. To lower the room temperature, press the bottom arrow of the TEMP button. At higher settings the heater will run longer.

seconds after lighting pilot. After 30

seconds, release control knob. Now

follow steps 9 through 11, page 18.

 

Control Knob

 

Flame Adjustment Knob

 

 

 

 

REMOTE

 

 

 

OL

N

 

 

 

OFF

 

 

 

O

 

F O

 

ON

T

 

 

 

O

 

F

 

 

L

 

HI

 

 

IP

 

Selector Switch in Remote

Position (Optional Remote Control)

Figure 38 - Setting the Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation

Continued

107034

19

For more information, visit www.desatech.com

Page 19
Image 19
Vanguard Heating VMH26PRA To Turn OFF GAS To Appliance, Manual Lighting Procedure, Optional Remote Operation