Vermont Castings Intrepid
Intrepid Multi-Fuel Clearance Chart
See Pages 14 and 16 for illustrations of these clearances.
| Unprotected Surfaces | Protected Surfaces | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| Stove Clearance |
|
| |
|
|
|
|
|
|
|
| |
| Stove Installed |
| Stove in | Stove Installed | Stove in | |||
| Parallel to Wall |
| Corner | Parallel to Wall | Corner | |||
|
|
|
|
|
|
|
|
|
| Side |
| Rear |
| Corners | Side | Rear | Corners |
No stove heat shields | (A) 24” |
| (B) 30” |
| (C) 20” | (D) 12” | (E) 16” | (F) 10” |
(610 mm) |
| (762 mm) |
| (508 mm) | (305 mm) | (410 mm) | (254 mm) | |
|
|
| ||||||
|
|
|
|
|
|
|
|
|
Top exit, rear stove h.s., | (G) 24” |
| (H) 16” |
| (I) 12” | (J) 12” | (K) 9” | (L) 10” |
(610 mm) |
| (410 mm) |
| (305 mm) | (305 mm) | (229 mm) | (254 mm) | |
connector with connector |
|
|
|
|
|
|
|
|
heat shields 1,2 |
|
|
|
|
|
|
|
|
Rear exit, rear stove | (M) 24” |
| (N) 14” |
| (NA) | (P) 12” | (Q) 9” | (NA) |
heat shield only 3 | (610 mm) |
| (356 mm) |
|
| (305 mm) | (229 mm) |
|
Top exit, rear stove | (G) 24” |
| (H) 16” |
| (I) 12” |
| * |
|
h.s., |
|
|
|
| ||||
(610 mm) |
| (410 mm) |
| (305 mm) |
|
|
| |
chimney connector5 |
|
|
|
|
| |||
|
|
|
|
|
|
|
| |
|
|
| Chimney Connector Clearance |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
connector, no |
| 26 “ (661 mm) |
| 12” (305 mm) |
| |||
connector heat shields |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
connector, with |
| 10” (254 mm) |
| 5” (127 mm)4 |
| |||
connector heat shields |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 12” (305 mm) |
|
| * |
| |||
connector5 |
|
|
|
| ||||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
| Front Clearance to Combustibles |
| |||||
|
|
|
|
|
|
|
| |
| All Installations | 48” (1219 mm) |
|
| ||||
|
|
|
|
|
|
|
|
|
* Clearances with
1.Shielding for a top exit stove must include the stove rear heat shield insert to protect the area behind the flue collar.
2.Chimney connector heat shields, in an installation that goes through a combustible ceiling, must extend to 1” (25 mm) below the ceiling heat shield, which is 22” (559 mm) in diameter. The ceiling heat shield should be 24 gauge or heavier sheet metal, centered on the chimney connector, and mounted on
3.Rear
4.The ceiling heat shield required when chimney connector shields are used should meet the wall protector. This will require trim- ming the ceiling shield along the line of intersection with the wall protector.
5.In top exit installations, this clearance requires the use of the rear heat shield with the shield insert installed.
2000970 | 13 |