Attaching the Wood Frame to the Door - DFUR Models
1.If the door is attached to the unit, remove by unscrewing the top allen head set screw at the top hinge. Remove the door by angling the door off of the bottom hinge pin.
2.Peel back the door gasket to expose the screw holes.
3.Set the wood frame flush to the front of the door in the desired location. Clamp the wood frame to the door if necessary.
4.Insert the wood screws through the back of the door into the pilot holes in the wood frame and tighten.
5.Reinstall the door gasket by pressing into the door channel. Make certain the corners are inserted fully.
6.Install the door to the unit. Use the supplied plastic washer as shown in the figure below.
7.Realigning the door may be necessary. Any final door adjustments can be made using a 1/8” allen head driver to adjust the door’s hinges. (See figure below)
8.Attach the door light striker plate as shown using the 5/16” hex or phillips head screws provided. Make certain the light is able to turn on a nd off when the door is opened and closed.
9.Attach the door to th e unit by reversing step number 1 above.
Hinge Hardware Installation
Details
CAUTION |
| CAUTION |
Door can become |
| Door can become |
disengaged if washers |
| disengaged if |
are not installed. |
| washers are not |
|
| installed. |
|
|
|
|
|
| Wood |
|
| ||
|
|
| Frame |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| Door Hinge | |||||
|
|
|
|
|
|
| |
|
|
|
|
|
| ||
|
|
|
|
| Shoulder bushing | ||
|
|
|
|
| 3/4” OD x 7/16” | ||
|
|
|
|
| ID Washer | ||
|
|
|
|
| 3/4” OD x 1/4” ID | ||
CAUTION |
|
|
|
| Washer | ||
Door may not swing properly |
|
|
|
|
| ||
|
| (3) Nylon hardware | |||||
if all nylon components are |
|
|
| components at | |||
not installed as shown |
|
|
| bottom hinge | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (2) Nylon |
|
|
|
|
|
| |||
|
| hardware |
| Magnetic door gasket | |||||||
Cabinet | |||||||||||
Hinge |
| components at |
|
| 3/8” clearance holes |
| |||||
|
| top hinge |
|
| for frame wood screws |
|
|
| |||
|
|
| |||||||||
|
|
|
|
|
|
|
| - 8 holes |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5/8”x 7/32” ID washer |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
|
|
| Shoulder |
|
|
|
|
| |||
|
|
| bushing |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
Door Hinge
Rear of Door
Wood Frame
Bottom Hinge Cover | Top Hinge Cover |
|
|
Door hinge adjustment screws
1/8” allen head screws for hinge adjustment
Door light striker plate
Attached wood |
| Bottom of |
frame |
| door |
|
|
|
|
|
|
8