Spare Battery Charger, Installation, Power Backup | VTech VT 1962

REPLACING THE BATTERY PACK

4.Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.

To purchase replacement battery packs, call VTECH Communications at 1-800-595-9511. In Canada, call VTECH Electronics at 1-800-267- 7377.

Spare Battery Charger

The VT 1962 has a built-in spare Battery Charger, which is located in the cradle of the Base Unit.

NOTE: In order to benefit from this feature, you must obtain an optional Spare Battery from an authorized VTech dealer, or by contacting VTech Customer Service at 1-800-595-9511 in the U.S.A and 1-800-267-7377 in Canada.

Installation

Remove the Spare Battery charger cover by pressing the release tab and lifting up.

			ANSWER
		MEMO	ON/OFF
CHARGING		SPARE	IN USE
CHARGING		BATTERY	IN USE
MAIL BOX1	MAIL BOX2		MAIL BOX3
	PLAY/STOP
DELETE	TIME/SET	SELECT	MENU
	TIME/SET	SELECT	MENU
REPEAT/SLOW	SKIP/QUICK		VOLUME
	PAGE

Place a battery pack in the Spare Battery charger. Make sure the metal charging contacts on the underside of the battery pack are aligned with the charging contacts in the Spare Battery charger.

			ANSWER
		MEMO	ON/OFF
CHARGING		SPARE	IN USE
CHARGING		BATTERY	IN USE
MAIL BOX1	MAIL BOX2		MAIL BOX3
	PLAY/STOP
DELETE	TIME/SET	SELECT	MENU
REPEAT/SLOW	SKIP/QUICK		VOLUME
	PAGE

Power Backup

When a Spare Battery pack is installed in the Base Unit, the VT 1962 uses this battery pack to provide operational backup in case of a power failure. If you have a fully charged battery pack in the Spare Battery pack charger and there is a power outage, you will still be able to place and receive calls for up to five hours.

Replacing a Drained Handset battery

The Spare battery pack can also be used to replace a drained Handset battery pack to ensure uninterrupted use. Be sure to put the drained battery pack in the Spare Battery charger for recharging.

Please note that the Spare Battery compartment charges at a slower rate than a battery pack charging in the Handset. It takes 24 hours to fully charge a battery pack in the Spare Battery charger.

11

Image 11

VTech VT 1962 manual Spare Battery Charger, Installation, Power Backup, Replacing a Drained Handset battery

Contents

Introduction MHz Operation Special Features Parts Check List FCC Part FCC and IC Regulations This telephone is registered for use in Canada IC Industry Canada FCC and IC Regulations Read and understand all instructions Important Safety Instructions If the product exhibits a distinct change in performance Its Impossible To Over-Charge The Battery Pack Replacing the Battery PackCharging The Handset Battery Pack To Charge The Battery Pack Replace the battery case cover by sliding the cover upwards Replacing a Drained Handset battery Spare Battery ChargerInstallation Power Backup Rbrctm Seal The Rbrcr Seal on the nickel-cadmium battery Getting Started Setting Up Your VTAC Power Adapter Setting the Tone/Pulse Switch Connect Telephone Line Cord Wall Mounting Using The Wall Mount Adapter LCD Display Messages LCD Display Handset Layout Handset Features Base Unit Layout Base Unit Features Quick Reference Guide To exit press OFF Using RedialMemory Dialing Speed Dialing CID Caller ID Basic Operation Temporary Tone Switching calls using FlashAdvanced Functions Call Waiting To turn off the ringer do the following Changing Ringer TypesTurning Off The Ringer Checking The Ringer Type Advanced Dialing CLR/DEL Key Function Press Phone to get a line Memory DialingDialing From Memory If programming is unsuccessful the unit will display Storing Special Codes Changing Stored NumbersDeleting Stored Numbers Receiving and Storing Calls CID-CALLER IDCall Waiting Caller ID Type II CID Word About Caller ID CID Private Calls Special Message Indicators Out of Area CallsTransmission Error Reviewing CID Records Reviewing Numbers Deleting Numbers Set Outgoing Message OGM Answering System SetupDefault Answering System Settings Answering System Program- ming Overview Day and Time Security code default setting is Set Announce Only Set Audible Message Alert Base ringer can be turned on or OFF Set Base Ringer On/OffSet Number of Rings Saving Messages Answering System OperationsLeaving a Message Incoming Message Listening to Messages / Memos Turning the Answering Machine Deleting Messages Changing Playback Speed Changing Speaker VolumeCall Screening Check Current Day and Time Memory Full Power Failure You have no new messages LED displays What it meansFlashing number Playing Messages Remotely Remote Operation of Answering System Memo Recording Repeat Messages During PlaybackSkip Messages During Playback Stop Message Playback Exiting Remote Operation Additional Operating Tips Belt Clip Headset OperationOperation Maintenance Phone Doesnt Work At All Handset Does Not Ring When You Receive a CallYou Hear Other Calls While Using Your Phone Case of Difficulty Common Cure For Electronic Equipment At our option, repair or replace your unit Warranty StatementAny defect in material or workmanship To the original purchaser only ONE Year What does OUR Warranty not COVER? Handset 295 grams Base 470 grams Technical SpecificationsCrystal Controlled Dual PLL Synthesizer Table of Contents Issue