Technical Specifications, Transmit Frequency Weight | VTech VT 9241

TECHNICAL SPECIFICATIONS

FREQUENCY CONTROL

•Crystal Controlled Dual PLL Synthe sizer

TRANSMIT FREQUENCY

WEIGHT

•Handset: 180 grams

•Base: 500 grams

POWER REQUIREMENTS

•Handset: 923.10 MHz to 927.75 MHz (All thirty channels within this range)

•Base: 902.3 MHz to 906.65 MHz (All thirty channels within this range)

RECEIVE FREQUENCY

•Handset: Self-contained nickel- cadmium rechargeable battery supply, 3.6V nominal, 400mAh ca- pacity.

•Power Adapter: 9V DC@500mA

•Handset: 902.3 MHz to 906.65 MHz (All thirty channels within this range)

•Base: 923.10 MHz to 927.75 MHz (All thirty channels within this range)

SPECIFICATIONS ARE TYPI- CAL AND MAY CHANGE WITH- OUT NOTICE.

NOMINAL EFFECTIVE RANGE

•Maximum power allowed by FCC. Actual operating range may vary according to environmental condi- tions at the time of use.

•The range quoted for this phone is Based on open field measurements under ideal conditions.

SIZE

•Handset: 17.3cm x 5.6cm x 3.8cm (L x W x T) maximum (antenna excluded)

•Base: 21.9cm x 16.4cm x 5.4cm (L x W x T) maximum (antenna excluded)

35

Image 35

VTech VT 9241 manual Technical Specifications, Transmit Frequency Weight, Power Requirements, Receive Frequency, Size

Contents

Introduction Features Wall Mounting Bracket Base Unit Battery pack Handset Belt clip AC adapterParts Check List Read and understand all instruc- tions Important Safety Instructions Rbrctm Seal If the product exhibits a distinct Change in performance Replacing the Handset Battery To install the Spare Battery Pack Spare Battery Charger Charge the Handset BATTER- IES Before USE. The batteries Getting Started Never install telephone wiring dur- ing a lightning storm Wall Mounting Handset Features Charge LED Base Unit FeaturesPower LED Spare Batt LED TONE/PULSE Switch OFF KEY Volume UP KEYVolume Down KEY Ringer Switches Making Calls Operating Instructions To PUT a Call on Hold Mute FeatureTips on Usingthe VT 9241 Speak Erphone Answer a Call From the Base Unit Pressing the VOL UP or Down keysMaking or Answering a Call While YOU’RE Already on a Call Ference Calling Joining a Conversation Press Hold on the HandsetPress the appropriate Line key on the Base Unit Using the Intercom Programming the Ringer Type Using the Intercom During a Phone CallTemporary Tone Feature If Your Phone Rings During AN Intercom Conversation Checking the Ringer Turning OFF the RingersTo turn off the ringer on the Handset do the following Press PGM/MEM Storing a Pause in a Speed Dial Number To Store a Number Into MemoryTo Speed Dial a Stored Number To Change or Replace a Stored Number Conference Calling Using RedialStoring a Redial Number in Memory Speed Dial Ending One Side Or Entire Confer- ence Call Switching a Conference Call From Handset To Base UnitSwitching a Conference Call From Base Unit To Handset Way Conference Calling Changing Channels Installation Optional Headset Installation and Operating Instructions ONE Inch Data Port Electrical Storms MaintenanceExcess water or cleaning solvents of any kind Taking Care of Your TELE- Phone No Dial Tone Handset does not Ring When YOU Receive a CallCase of Difficulty Phone DOESN’T Work AT ALL Your Caller Fades in and OUT YOU Hear Other Calls While Using Your PhoneBase does not Ring Common Cure for Electronic Equipment Warranty Statement HOW does State LAW Relate to this WARRANTY? What does OUR Warranty not COVER? FCC Part FCC and IC RegulationsUnited States Canada Vtech Electronics This telephone is registered for use in Canada IC Industry Canada Office Receive Frequency Technical SpecificationsTransmit Frequency Weight Power Requirements Table of Contents If Your Phone Rings During AN Intercom Conversation 91-5073-10-00 Issue