FLAME CURRENT MEASUREMENT

 

 

 

 

 

 

 

 

 

 

 

MICROAMP METER

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

10

 

 

 

 

 

 

 

 

 

 

 

S1

 

 

 

 

 

 

56

 

FENWAL

 

 

 

 

 

 

 

 

 

 

DUAL

LED

 

 

 

 

 

56

 

55

8

V2

CHANNEL

RED DIAGNOSTIC INDICATOR

52

 

 

345519-4

C-2

 

 

57

59

W

IGNITION

 

T

 

 

 

 

 

 

 

 

NC

 

 

 

 

U

424471-G1

 

 

 

 

 

S1

MODULE

 

LEFT

RIGHT

 

 

1

2

3

S1

S2

 

 

 

 

 

 

 

BURNER

BURNER

 

 

 

 

 

 

S2

 

 

 

 

 

 

 

 

 

 

SPARK

SPARK

 

 

 

2

 

 

 

 

 

 

OUT

OUT

48

 

 

 

 

 

 

 

 

 

 

 

S2

 

 

3

2

 

 

 

 

 

 

 

X

 

 

TH

 

 

 

 

 

D

 

 

 

 

1

 

 

 

 

 

 

Y

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

L

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

V

6

57

 

 

L1

L2

 

 

 

 

 

5

 

 

 

48

 

 

 

 

 

 

 

 

 

 

 

 

 

W 120 VOLT UNITS PROVIDED

 

46

 

 

GND.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WITH 3 PRONG GROUNDED

 

 

WHITE

PLUG.

AB

GREEN

BLACK

 

AB

417856-1

CONNECT 200-240 VOLT

SUPPLY TO L1 & L2

1.Use a Microampere (µamp) meter to measure the flame current on both wires S1 & S2.

2.Connect a Microampere meter as shown above to S1 & S2, to read the actual flame current of each igniter.

3.The ignition system is 1 µamp sensitive.

4.You should be able to attain a reading of 4 µamps when connected as shown.

5.The meter is to be placed in series with the flame sense wires S1 & S2.

6.Connect at the board or the igniter end,

whichever is more convenient.

BLOWER ADJUSTMENT

Disconnect the electrical power to the machine and follow lockout / tagout procedures.

1.Remove the blower motor and mounting assembly as outlined under Blower and Motor in Removal and Replacement of Parts.

2.Loosen the motor mounting bolts.

3.Adjust the motor position until the blower is parallel to and 1/4" inch away from the motor mounting plate. Check to see if the blower is square to the motor mounting plate at the top, bottom, left and right of the blower.

A.If the blower is square, then tighten motor mounting bolts and proceed to step 4.

B.If the blower is not square, continue adjusting until proper spacing is achieved then tighten motor mounting bolts. If necessary, place shims between motor and frame.

PLACE SHIMS UNDER REAR OF

1/4 INCH AT

ALL PLACES

MOTOR TO WIDEN TOP SPACE.

 

 

 

TOP

 

FLAT

 

 

WASHER

 

 

MOTOR

BLOWER

 

FRAME

 

 

 

FLAT WASHER

 

PLACE SHIMS HERE

NUT/STAR

 

WHEN NEEDED.

WASHER

BOTTOM

PLACE SHIMS UNDER FRONT OF

 

MOTOR TO WIDEN BOTTOM SPACE.

 

 

MOTOR MOUNTING PLATE

 

 

 

PL-56058

4.Reverse the procedure to install. Use locktight on mounting nuts and bolts.

– 27 –

Page 27
Image 27
Vulcan-Hart SG4D service manual Flame Current Measurement, Blower Adjustment