Operating Instructions and Parts Manual | Cast Iron Utility Series |
|
|
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or prop- erty damage! Retain instructions for future reference.
Self-Priming Portable
Utility Pump
Description
This
NOTE: This pump is not intended for permanent installation or long, extend- ed periods of continuous operation.
Safety Guidelines
This manual contains information that is very important to know and under- stand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this infor- mation, observe the following symbols.
Danger indicates an imminently haz-
ardous situation which, if not avoided, will result in death or serious injury.
Warning indicates a potentially haz-
ardous situation which, if not avoided, could result in death or serious injury.
Caution indicates a potentially haz-
ardous situation which, if not avoided, may result in minor or moderate injury.
Specifications
Notice indicates important informa-
tion, that if not followed, may cause
damage to equipment.
General Safety
Information
Do not submerge motor or allow
motor to be exposed to water. Personal injury and/or death could result.
Do not use to pump flam- mable or explosive fluids such as gasoline, fuel oil, kerosene, etc. Do not use
in a flammable and/or explosive atmos- phere. Pump should only be used to pump clear water. Personal injury and/or death could result.
Risk of electrical shock. All wiring
must be performed by a qualified elec- trician.
Do not walk on wet areas until all power is turned off. Failure to fol- low this warning could result in fatal electrical shock.
1.Read all instructions before operation.
2.Disconnect power and release all pressure within the system before servicing any component.
3.Drain all liquids from system before servicing.
Secure the dis- charge line before
starting the pump. An unsecured dis- charge line may whip. Personal injury and/or property damage could result.
4.Periodically inspect pump and sys- tem components, checking for weak and/or worn hoses. Insure all connections are secure.
5.Provide a means of pressure relief in the case of an obstructed dis- charge line.
6.Protect electrical cord from sharp objects, hot surfaces, oil and chemi- cals. Avoid kinking the cord and replace damaged cords immediately.
Installation
Always disconnect power source before attempting to install, service, or maintain the pump. Never handle a pump with wet hands or when standing on wet or damp sur- face or in water. Fatal electrical shock could occur.
1.A ground fault circuit interrupter (GFCI) is required.
Risk of electrical shock! This pump is supplied with a grounding conduc
Motor . . . . . . . . . . . . . .Single Phase - 115V, 60 Hz, 8,000 RPM . . . .Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/2 HP Motor . . . . . . . . .Series Wound (brush type) AC/DC Operation . . . .Inlet/Outlet Openings . . . . . . . . . . . . . . . . . . . . . . .3/4” NPT Impeller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SAN . . . .Pump Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cast iron Motor Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cast iron . . . .Motor Shaft . . . . . . . . . . . . . . . . . . . . . . . .Cold rolled steel Shaft and Volute
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2005 Wayne Water Systems | For parts, product & service information |
visit www.waynepumps.com
